Inhaltszusammenfassung für HANSGROHE Logis E 100 71161003
Seite 1
EN Instructions for use / Assembly instructions DE Gebrauchsanleitung / Montageanleitung Logis E 100 Logis E 70 Novus 70 Novus 100 71161003 71160003 71021003 71031003 Ecos L CoolStart Ecos M CoolStart 14043003 14042003 31517003 31730003...
Seite 2
English Operation (see page 7) Safety Notes • Hansgrohe recommends not to use as drinking water Gloves should be worn during installation to prevent the first half liter of water drawn in the morning or crushing and cutting injuries. after a prolonged period of non-use. The product may only be used for bathing, hygienic • After periods of prolonged non-use, but at least and body cleaning purposes. every third day, the fittings must be opened with the The hot and cold supplies must be of equal handle in hot and cold position to prevent stagnation pressures. in the connecting lines. Let the water run until the Installation Instructions water temperature is constant. • Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honoured. • The pipes and the fixture must be installed, flushed and tested as per the applicable standards. • The plumbing codes applicable in the respective countries must be observed. Technical Data Operating pressure: max. 1 MPa Recommended operating pressure: 0,1 - 0,5 MPa Test pressure: 1,6 MPa (1 MPa = 10 bar = 147 PSI) Hot water temperature: max. 60°C Thermal disinfection: 70°C / 4 min...
Seite 3
Deutsch Bedienung (siehe Seite 7) Sicherheitshinweise • Hansgrohe empfiehlt, morgens oder nach längeren Bei der Montage müssen zur Vermeidung von Stagnationszeiten den ersten halben Liter nicht als Quetsch- und Schnittverletzungen Handschuhe Trinkwasser zu verwenden. getragen werden. • Um eine Stagnation in den Anschlussleitungen zu Das Produkt darf nur zu Bade-, Hygiene- und vermeiden, muss nach längeren Gebrauchspausen, Körperreinigungszwecken eingesetzt werden. mindestens aber jeden dritten Tag, die Armatur in Große Druckunterschiede zwischen den Kalt- und Griffstellung heiß und kalt geöffnet werden bis eine Warmwasseranschlüssen müssen ausgeglichen gleichbleibende Auslauftemperatur erreicht ist. werden. Montagehinweise • Vor der Montage muss das Produkt auf Transport- schäden untersucht werden. Nach dem Einbau werden keine Transport- oder Oberflächenschäden anerkannt. • Die Leitungen und die Armatur müssen nach den gültigen Normen montiert, gespült und geprüft werden. • Die in den Ländern jeweils gültigen Installationsricht- linien sind einzuhalten. Technische Daten Betriebsdruck: max. 1 MPa Empfohlener Betriebsdruck: 0,1 - 0,5 MPa Prüfdruck: 1,6 MPa (1 MPa = 10 bar = 147 PSI) Heißwassertemperatur: max. 60°C...
Seite 4
98996000 (7 Nm) SW 23 mm SW 9 mm (4 Nm) SW 22 mm...
Seite 6
60 °C 10 °C 0,3 MPa 36°C 38°C 50°C 60°C 43°C 55°C 17 x...
Seite 7
31517003 / 31730003 / Novus 70 71021003 / Novus 100 71031003 / Logis E 70 71160003 / Logis E 100 71161003 open / öffnen close / schließen hot / warm cold / kalt Ecos M CoolStart 14042003 / Ecos L CoolStart 14043003 open / öffnen close / schließen hot / warm cold / kalt...
Seite 8
31517003 31730003 Ø 3 4 G 1 / 2 G 1 / 2 Ecos M CoolStart Ecos L CoolStart 14042003 14043003 Ø 3 4 Ø 3 4 G 1 / 2 G 1 / 2...
Seite 9
Novus 70 Novus 100 71021003 71031003 Ø 3 4 Ø34 G 1 / 2 G1/2 Logis E 70 Logis E 100 71160003 71161003 Ø 48 Ø 3 2 Ø 3 2 G 1 / 2 G 1 / 2...