Disposal And Recycling; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TE-CL 18/2000 LiAC Originalbetriebsanleitung

4.7 Fastening the lamp
The lamp can be fastened quickly and easily in
various ways via the diff erent cutouts on the bot-
tom of the foot.
•
Hook (Fig. 6 / item 14): The hook can be used
for quick and easy attachment of the lamp to
e.g. a railing or scaffolding.
•
Sawtooth (Fig. 7 / item 15): The sawtooth cu-
tout can be used to hang the lamp to a nail or
similar. The fine tooth spacing allows the lamp
to be perfectly balanced.
•
Fastening eyelet (Fig. 8 / item 16): The faste-
ning eyelet can be used to attach the lamp to
the wall with a suitable pan head screw.
•
Threaded bushes, ¼" and ⅝" (Fig. 9 /
item 17): The threaded bushes can be used
to mount the lamp on a stand.
4.8 Battery capacity indicator (Fig. 10)
Press the battery capacity indicator switch (a).
The battery capacity indicator (b) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The battery temperature is too high. Remove the
battery from the unit and keep it at room tempera-
ture for one day. If the fault occurs again, the bat-
tery has been deep-discharged and is defective.
Remove the battery from the unit. Never use or
charge a defective battery.
5. Cleaning, maintenance and
ordering of spare parts
Danger!
Always remove the battery pack before starting
any cleaning work.
5.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
Anl_TE_CL_18_2000_LiAC_SPK13.indb 14 Anl_TE_CL_18_2000_LiAC_SPK13.indb 14
GB
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
5.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
5.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com

6. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
7. Storage
Store the equipment and accessories in a dark
and dry place at above freezing temperature.
The ideal storage temperature is between 5 and
30 °C. Store the electric tool in its original pa-
ckaging.
- 14 -
06.07.2022 10:21:55 06.07.2022 10:21:55