Technical Data; Maintenance And Cleaning - Conrad 55-25-22 Bedienungsanleitung

Controls
1 Safety plug for connection to the
mains socket
2 Switch for selection of operating
mode "Countup" or "Countdown"
3 Sliding switch for setting of the
countdown time
4 Safety plug for connection to the
consumer
5 Control LED
6 Touch button to start/stop the
countdown
Getting Started, Use
Follow the safety instructions and the other information in this operation manual.
• First, select the operating mode with the sliding switch (2).
"Countup": The consumer is switched on after the set time has elapsed.
"Countdown": The consumer is switched off after the set time has elapsed.
• Plug the countdown timer into an appropriately earthed mains socket (wall socket) with its
mains plug (1).
• Plug the consumer into the socket (4) on the front of the countdown timer; make sure the plug
is pushed into the socket fully.
• If the consumer connected to the countdown timer has a power switch, switch it on (the
switch setting marked e.g., "ON" or "I").
• Select the desired countdown time with the sliding switch (3) at the side. A time of 0.5h, 1h,
3h or 6h can be set.
• Start the countdown timer by briefl y touching the touch button (6) on the top.
The function depends on the operating mode you have selected with the sliding switch (2) on
the back:
Operating mode "Countup":The LED (5) starts to fl ash. The consumer remains switched
off and is switched on after the countdown time has elapsed; the LED (5) is permanently
illuminated.
Operating mode "Countdown": The consumer is switched on immediately, the LED (5) is
illuminated. After the countdown time has elapsed, the consumer is switched off automati-
cally, the LED (5) goes out.
☞
The countdown can be stopped early at any time by touching the touch button (6).
The countdown timer and the connected consumer are switched off; the LED (5)
goes out.
If the touch button (6) is touched again, the countdown timer restarts with the set
operating mode and countdown time.
If the countdown is already active and you move the sliding switch (3), the set time
is increased or decreased automatically.

Maintenance and Cleaning

• The product does not require maintenance. The product contains no parts that require servic-
ing. Therefore, do not open/dismantle it. Maintenance or repairs may only be performed by
qualifi ed personnel or a specialised repair shop.
• Before cleaning, disconnect the countdown timer from the power supply. To do this, unplug it
completely from the mains socket (the wall socket).
• Use a clean, dry, soft cloth for cleaning.
• Dust can easily be removed using a clean, soft and long-bristled brush and a vacuum cleaner.
Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions,
since these could damage the housing or even impair operation.
All manuals and user guides at all-guides.com
Disposal
2
3

Technical Data

Operating voltage .........................230 V/AC, 50 Hz
1
Switching capacity ........................max. 3680 W
Protection class ............................I
Model: ...........................................Relay; 1-pole disconnection
Countdown timer ..........................0.5h, 1h, 3h, 6h
Tolerance ......................................±3%
Ambient temperature ....................0 °C to +40 °C
Ambient humidity ..........................0% to 90% relative humidity, not condensing
Dimensions ...................................65 x 118 x 40 mm (W x H x D), without mains plug
Weight ..........................................approx. 140 g
4
5 6
Dispose of the unserviceable product according to the relevant statutory regulations!
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.