Product Description And Specifications - Bosch GSA 18 V-LI C Professional Originalbetriebsanleitug

Safety instructions for sabre saws
Hold the power tool by insulated gripping surfaces,
u
when performing an operation where the cutting ac-
cessory may contact hidden wiring. Cutting accessory
contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an elec-
tric shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the workpiece by hand or against your body leaves it un-
stable and may lead to loss of control.
Keep hands away from the sawing area. Do not reach
u
under the workpiece. Contact with the saw blade can
lead to injuries.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Ensure that the footplate is always resting on the
u
workpiece while sawing. The saw blade can jam and
lead to loss of control over the power tool.
When the cut is completed, switch off the power tool
u
and then pull the saw blade out of the cut only after it
has come to a standstill. In this manner you can avoid
kickback and can place down the power tool securely.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Use only undamaged saw blades that are in perfect
u
condition. Bent or dull saw blades can break, negatively
influence the cut, or lead to kickback.
Do not brake the saw blade to a stop by applying side
u
pressure after switching off. The saw blade can be dam-
aged, break or cause kickback.
Ensure that the material is securely clamped. Do not
u
support the workpiece using your hands or feet. Do
not touch any objects or the floor with the saw while it
is running. There is a risk of kickback.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Bosch Power Tools
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is suitable for sawing wood, plastic, metal
and building materials on a firm surface. It is suitable for
straight and curved cuts. When using designated suitable bi-
metal saw blades, flush cutting is also possible. The saw
blade recommendations are to be observed.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
A)
(1) Saw blade
(2) Base plate
(3) Locking sleeve for saw blade
A)
(4) Battery
(5) Lock-off button for on/off switch
(6) On/off switch
(7) Worklight
(8) Battery release button
(9) Handle (insulated gripping surface)
(10) Button for battery charge indicator
(11) Battery charge indicator
(12) Saw blade receptacle
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Reciprocating saw
Article number
Rated voltage
No-load stroke rate n
Tool holder
Stroke
Автотовары «130»
English | 13
A)
A)
A)
GSA 18 V-LI C
3 601 FA5 0..
V=
−1
min 0–3050
0
mm
1 609 92A 4TC | (02.04.2019)
18
SDS
21