Noise/Vibration Information; Changing The Tool - Bosch PMF 180 E Multi Originalbetriebsanleitung

OBJ_BUCH-2236-001.book Page 12 Thursday, October 20, 2016 9:42 AM
12 | English

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); Sound power level 96 dB(A).
Uncertainty K <1.5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-4:
2
Sanding: a =6.4 m/s , K<2.0 m/s
h
Sawing with plunge cut saw blade: a
2
K<1.5 m/s ,
Sawing with segment saw blade: a
2
Scraping: a =11.4 m/s , K=2.2 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
Assembly

Changing the Tool

 Before any work on the machine itself, pull the mains
plug.
Selecting the Application Tool/Accessory
The following table shows examples for application tools. Further application tools can be found in the extensive Bosch acces-
sories program.
Accessory
BIM segment saw
blade
Base plate for sand-
ing, series Delta
93 mm
HCS plunge cut saw
blade, wood
HCS plunge cut saw
blades, wood
BIM plunge cut saw
blades, metal
HM-Riff segment
saw blade
1 609 92A 2WK | (20.10.16)
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
2
,
when it is running but not actually doing the job. This may sig-
2
=9.9 m/s ,
nificantly reduce the exposure level over the total working
h
period.
2 2
=5.0 m/s , K<1.5 m/s ,
Identify additional safety measures to protect the operator
h
2
.
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
 Wear protective gloves when changing application
Material Application
Wooden materials, plas- Separating and plunge cuts; also for sawing close to edges,
tic, non-ferrous metals in corners and hard to reach areas;
example: shortening already installed bottom rails or door
hinges, plunge cuts for adjusting floor panels
Depends on sanding sheet Sanding surfaces close to edges, in corners or hard to reach
areas;
depending on the sanding sheet for, e.g., sanding wood,
paint, varnish, stone
Wooden materials, soft Separating and deep plunge cuts; also for sawing close to
plastics edges, in corners and hard to reach areas;
example: narrow plunge cut in solid wood for installing a
ventilation grid
Wooden materials, soft Smaller separating and plunge cuts;
plastics example: cut-outs in furniture for cable connections
Metal (e. g. unhardened Smaller separating and plunge cuts;
nails, screws, smaller pro- example: shortening narrow profiles, cutting fastening
files), non-ferrous metals elements such as staples
Grouting joints, soft wall Cutting and separating close to edges, in corners or hard to
tiles, glass-fibre reinforces reach areas;
plastic and other abrasive example: removing grouting joints between wall tiles for
materials repair work, cutting openings in tiles, gypsum boards or
plastic
tools/accessories. Contact with the application tool/ac-
cessory can lead to injuries.
Bosch Power Tools