EINHELL EF 1800 Originalbetriebsanleitung Seite 24

the switch ON time for Monday in minutes.
Switch OFF time
•
Press the "TIMER" or "7" button again within
5 seconds. The "Mon" LED and the hours
display will flash.
•
Press "UP" (K) or "DOWN" (L) to set the
switch OFF time for Monday in hours.
•
Press the "TIMER" or "24H" button and use
"UP" (K) and "DOWN" (L) to set the switch
OFF time for Monday in minutes.
Press the "TIMER" or "7" button again to program
Tuesday. Repeat these programming steps for all
the other days of the week.
To skip a day of the week (e.g. Tuesday) when you
are programming, press the "TIMER" or "7" button
as often as necessary until the next day you want
to program (e.g. Wednesday) appears.
6.7.2 Programming weeks using the remote
control (Fig. 9)
Note: In addition to programming days as
described above, you can also program the
switch ON and OFF times on a weekly basis as
well using the remote control.
Programming the hour switch ON time
(Fig. 9)
•
Press the "7" button. The "Mon" LED and the
hours display will flash.
•
Press the "UP" (K) or "DOWN" (L) buttons to
set the switch ON time for Monday in hours.
•
Press the "7" button again. Program Tuesday.
•
Repeat these programming steps for the
other days of the week.
•
Once all the days of the week have been
programmed, the current setting will be saved
automatically after 5 seconds (do not press
any of the buttons).
Programming the minutes switch ON time
(Fig. 9)
•
Press the "7" button and then "24H". The
"Mon" LED and the minutes display will flash.
•
Press the "UP" (K) or "DOWN" (L) buttons to
set the switch ON time for Monday in minutes.
•
Press the "7" button again and then "24H".
Program Tuesday.
•
Repeat these programming steps for the
other days of the week.
•
Once all the days of the week have been
programmed, the current setting will be saved
automatically after 5 seconds (do not press
Anl_EF_1800_SPK9.indb 24 Anl_EF_1800_SPK9.indb 24
GB
any of the buttons).
Programming the hour switch OFF time (Fig.
9)
•
Press the "7" button and then press the "24H"
button twice. The "Mon" LED and the hours
display will flash.
•
Press the "UP" (K) or "DOWN" (L) buttons to
set the switch OFF time for Monday in hours.
•
Press the "7" button again and then press
"24H" twice. Program Tuesday.
•
Repeat these programming steps for the
other days of the week.
•
Once all the days of the week have been
programmed, the current setting will be saved
automatically after 5 seconds (do not press
any of the buttons).
Programming the minutes switch OFF time
(Fig. 9)
•
Press the "7" button and then press the "24H"
button three times. The "Mon" LED and the
minutes display will flash.
•
Press the "UP" (K) or "DOWN" (L) buttons
to set the switch OFF time for Monday in
minutes.
•
Press the "7" button again and then press
"24H" three times. Program Tuesday.
•
Repeat these programming steps for the
other days of the week.
•
Once all the days of the week have been
programmed, the current setting will be saved
automatically after 5 seconds (do not press
any of the buttons).
6.8 Setting the current time (Fig. 9)
Note: This can only be set on the equipment.
If no button is pressed for 5 seconds the current
setting will be saved automatically.
•
Switch off the heater with the "POWER"
button (D).
•
Press the "TIMER" button for 3 seconds. The
hours display will flash for 5 seconds.
•
Use the "UP" and "DOWN" buttons to set the
current hour.
•
Press the "TIMER" button; the minutes display
will flash for 5 seconds.
•
Use the "UP" and "DOWN" buttons to set the
current minutes.
•
Press the "TIMER" as often as necessary
until the LED for the current day of the week
appears. The hours and minutes displays
flash alternately during this time.
- 24 -
22.11.2018 06:58:50 22.11.2018 06:58:50