Technical Data; Operation; Before Starting The Machine - EINHELL BG-PH 2250 Bedienungsanleitung

Anleitung_BG-PH_2250_SPK1:_
GB

4. Technical data

Engine type:
2-stroke engine, air-cooled, chrome cylinder
Engine output (max.):
Displacement:
Idle speed of engine:
Max. engine speed
Weight (with empty tank):
Cutting length:
Tooth spacing:
Vibration (front handle) a
hv
Vibration (rear handle) a
hv
Sound pressure level L
pA
Sound power level L
WA
Sound and vibration were measured in accordance
with DIN EN 10517.

5. Before starting the machine

5.1 Fuel and oil
Recommended fuels
Use only a mixture of normal unleaded petrol and
special 2-stroke engine oil. Mix the fuel mixture as
indicated on the fuel mixing table.
Please note: Do not use a fuel mixture which has
been kept for longer than 90 days.
Please note: Do not use 2-stroke oil with a
recommended mixing ration of 100:1. If inadequate
lubrication causes engine damage, the
manufacturerʼs engine warranty will be voided.
Please note: Only use containers designed and
approved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke oil
into the mixing bottle (see scale printed on the
bottle). Then shake the bottle well.
5.2 Fuel mixture table
Mixing procedure: 40 parts petrol to 1 part oil
Petrol
1 liters 25 ml
5 liters 125 ml
14
15.10.2008 8:28 Uhr

6. Operation

Please note that the statutory regulations governing
noise abatement may differ from town to town.
0.65 kW / 0.9 hp
6.1 Starting the engine from cold (Fig. 3-5)
22 cc Fill the tank with the required amount of oil/petrol
mix.
3000 min -1
1. Set the machine down on a hard, level surface.
8500 min -1
2. Set the choke lever (Fig. 4/Item 5) to " ".
5.6 kg
3. Press the fuel pump (primer) (Fig. 4/Item 9) 10
50 cm times.
4. Move the ON/OFF switch (Fig. 3/Item 6) to "I"
28 mm
5. Set the throttle lever to full throttle. To do so,
7.63 m/s 2
press the throttle lock (Fig. 3/Item 13).
5.01 m/s 2
6. With the other hand pull out the starter cable (Fig.
95 dB 5/Item A) until you feel it starts to resist. Now pull
the starter cable repeatedly until the equipment
106 dB
starts up.
Important: Never allow the starter cable to snap
back. This may damage the equipment.
7. If the engine has started, set the choke lever
immediately to "
warm up for approx. 10 seconds.
8. If the engine does not start up, repeat steps 6-7
above.
Please note: If the engine does not start up even
after several attempts, read the section "Engine
Troubleshooting".
Please note: Always pull the starter cable out in a
straight line. If it is pulled out at an angle, then friction
will occur on the eyelet. As a result of this friction, the
cable will become frayed and will wear away faster.
6.2 Starting the engine when warm (if the
machine has not been switched off for more than
15 – 20 minutes)
1. Set the machine down on a hard, level surface.
2. Switch the ON/OFF switch to "I".
3. Hold the machine by the front handle in your
right hand and pull the starter cable up to the first
resistance point (approx. 10 cm). Then tug
sharply on the starter cable. The machine should
start after 1-2 tugs. If the machine does not start
after 6 pulls, repeat steps 1 – 7 of the procedure
for starting the engine from cold.
2-stroke oil
6.3 Switching off the engine
Emergency Stop procedure:
If it becomes necessary to stop the machine
immediately, set the ON/OFF switch to "Stop" or "0"
Seite 14
" and allow the machine to