Installation And Connection - Conrad 75 18 01 Bedienungsanleitung

Installation and Connection

Overview of the assembly of your camera:
Find a suitable place for mounting from which the area to be monitored can be observed. A
suitable place for installation of this camera has the following features:
• Vibration-free
• No direct sunlight
☞
Select a mounting location that is not shielded, for example, by reinforced concrete
walls, stea med up mirrors or metal shelves. There should be no devices that pro-
duce strong electrical fi elds, such as mobile telephones, radios or electrical motors,
close to the device. This can disturb the radio transmission or limit the range. Heat
sources can cause malfunctions or defects.
Do not point the camera directly toward a source of bright sunlight or towards strong
or indirect illumination as this may lead to overexposure and a fuzzy picture.
Mounting the radio camera
None of the connection cables must be bent or squeezed. This can result in
malfunctions, short circuits and defects in the device.
Make sure that cables are not damaged when drilling or bolting into place.
Ensure that the plug and socket of the camera's connection cable are not ex-
posed to dampness. Plugs and sockets may only be used indoors. The came-
ra cable must (for installation in outdoor areas or in damp rooms) be placed
so it is led into a dry room.
Do not point the camera directly toward a source of bright sunlight or toward
strong or indirect illumination as this may lead to overexposure and a fuzzy
picture.
Wall mounting:
Ceiling mounting:
Connecting the wireless camera
• Connect the supplied power unit's low-voltage connector to the „DC IN 5 V" (7) power con-
nection on your wireless camera.
• Insert the plug-in power unit into a suitable mains socket.
Maintenance and Cleaning
Before cleaning the housing of the surveillance camera, remove it from the mains voltage and
disconnect the power transformer from the mains socket.
To clean the outside of the camera, it is suffi cient to use a dry, soft and clean cloth.
Clean the lens very carefully, otherwise you may scratch it. Do not use any aggressive cleaning
agents.
• Find a suitable location for
mounting the ca mera.
• The mounting bracket has
mounting ho les. Mark these
(e.g. with a pencil) on the wall.
• Drill the mounting ho les into the
wall.
• Fasten the mounting bracket to
the wall with suitable moun ting
material.
• Attach the camera to the moun-
ting bracket.
• Adjust the camera to the
desired position.
• Tighten the fast e ning screws of
the moun ting bracket.
Disposal
Dispose of the product at the end of its serviceable life according to the relevant
legal provisions and regulations (e.g. return it to a special recycling facility in your
town).
Technical Data
a) Camera
Operating voltage: ................ 5 V/DC
Frequency: ............................ 2.4 GHz
Detection area, horizontal: .... 56° (+/-3°)
Detection area, vertical: ........ 43° (+/-3°)
Resolution: ............................ 640 x 480 (VGA), 320 x 240 (QVGA); these indications apply in
connection with the radio system: Conrad Item no.: 75 18 00
Radio range: ......................... max. 200 metres (free fi eld)
Degree of protection: ............ IP44 (suitable for operation in outdoor locations)
Operating temperature: ........ -10° to +50°C
Weight: ................................. approx. 145 grams (without rain cover, without antenna)
Dimensions: .......................... approx. 146 x 68 x 36 mm
b) Power supply
Operating current: ................ 100 - 240 V/AC, 50/60 Hz
Exit: ...................................... 5V/DC, 1A
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the fundamental requirements and the other relevant regulations of the
directive 1999/5/EG.
☞
You can fi nd the declaration of conformity for this product at www.conrad.com.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.