Conrad RSLR2 Bedienungsanleitung Seite 3

O P E R A T I N G I N S T R U C T I O N S
Remote controlled socket switch
RSLR2
Item no. 64 04 66
Intended use
This remote controlled socket switch is intended for switching connected consumer loads on or
off, either manually via a push button on the device or via a suitable remote switch.
The remote controlled socket switch is only intended for use in dry indoor spaces.
All the safety and operating instructions in this manual must be followed carefully. These
instructions not only protect the device but, in particular, your health. Please read the entire
operating manual before using the product.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• 1 x Remote controlled socket switch
• Operating Instructions
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. In such cases,
the warranty will be null and void.
• The unauthorized opening, conversion and/or modifi cation of this product is not
permitted because of safety and approval reasons (CE).
• The remote controlled socket switch is designed in accordance with protection
class I. Only a standard mains socket (230V/AC, 50 Hz with protective earth) for
the public supply grid may be used as a power source.
• The product is not a toy and must be kept out of the reach of children. Therefore,
be especially careful when children are around. Children might try to push objects
through the socket openings for example. There is a risk of a lethal electric shock!
• The remote controlled socket switch is only intended for use in dry indoor spaces.
• Never touch the remote controlled socket switch, or the mains plug, with wet or
damp hands when trying to connect a plug to the front socket. There is a risk of a
lethal electric shock!
• Never remove a mains plug from the front of the remote controlled socket switch
by pulling on the power cable. Always pull the plug from the socket, in the remote
controlled socket switch, using the gripping surface provided on the side.
• Don't connect adaptor plugs in series!
• The device is only voltage-free when its plug is pulled out of the mains socket.
• Do not overload the remote controlled socket switch (take note of the input power
in the technical data at the end of the operating manual!).
• Do not leave packaging material carelessly lying around since it could become a
dangerous plaything for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
• If the product casing is damaged, do not use the product anymore! When it is
connected to the mains, do not touch the remote controlled socket switch or the
connected device! First, switch off the mains socket to which the remote controlled
socket switch is connected (switch off at the circuit breaker). You can then remove
the remote controlled socket switch from the mains socket. Take the product to a
specialist workshop or dispose of it in an environmentally friendly way.
Controls
www.conrad.com
Version 01/12
1) "ON/OFF/INDICATOR" button/LED
By using this button, the remote controlled socket switch can be activated or deactivated
manually. This button also serves as the programming button.
2) Front socket for connecting a consumer load with child-proof lock
Programming the Remote Controlled Socket Switch to a Radio
Transmitter
• Set the switch group on the transmitter, to which you want to program the remote controlled
socket switch, if necessary (e.g. for a radio remote control) using the selector switch for the
switch group.
• Plug the remote controlled socket switch into a standard 230 V/AC 50 Hz household socket.
The LED (1) starts to blink.
• Press the ON button for the desired switching channel on the radio transmitter, i.e. that to
which you want to program the remote controlled socket switch before the LED stops blink-
ing. The red LED (1) lights up. The programming has been completed successfully.
Programming a Remote Controlled Socket Switch to Recognise
Several Radio Transmitters
☞
• Set the switch group on the transmitter, to which you want to program the remote controlled
socket switch, if necessary (e.g. for wireless remote control) using the selector switch for the
switch group.
• Plug the remote controlled socket switch into a standard 230 V/AC 50 Hz household socket
and press the button (1) until the LED starts to blink red.
• Press the ON button for the desired switching channel on the radio transmitter, i.e. that to
which you want to program the radio socket switch, before the LED stops blinking. The LED
(1) lights up. The programming has been completed successfully.
Deleting Programmed Remote Controlled Switch Sockets from
a Radio Transmitter
Please observe the operating instructions for the corresponding radio transmitter.
Start-up, Function Test
Select the correct switch group on the transmitter, if necessary (e.g. on a radio remote control).
Plug the remote controlled socket switch (without the consumer load connected!) into the desig-
nated earthed mains socket.
You can now test the function of the remote controlled socket by briefl y pressing the respective
ON button for the corresponding switching channel. The red LED (1) lights up. The socket (2)
on the front is now activated; the mains voltage is available and a connected consumer load
is turned on.
Briefl y press the OFF button, for the corresponding switching channel on the transmitter; the
LED (1) is turned off again; the mains voltage to the front socket (2), and thus the connected
consumer load, is turned off.
Up to 10 radio channels can be programmed for the remote controlled socket
switch.