Conrad TurbiTwin Bedienungsanleitung Seite 3

(11) Remove the shake attachments (H) when using the blades
to chop or mix non-liquid ingredients. See Figure 3.
(12) Turn off the appliance before changing the attachments or
handling the moving parts.
(13) Only use the appliance with both blade shafts in place. Ne-
ver attempt to use it with just one blade.
(14) For safety reasons, only a qualified professional should re-
pair the appliance. If the appliance needs to be adjusted in any
way, or if it stops working, contact a specialized technician.
(15) If the power cable is damaged, it must only be replaced by
a cable provided by the manufacturer, service agent or other
qualified person, to avoid hazards.
(16) Only use the attachments that came with the food mul-
tiprocessor.
(17) This appliance should not be used by children or people
whose mental, sensory or physical faculties prevent them from
using it safely. Children should not be allowed to play with the
appliance.
WARNING: Use the appliance according to the instructions.
Excessive use of the appliance is a hazard. Take care when han-
dling the blades, particularly when removing them from the
container, emptying the container and when cleaning them.
(C) Assembly instructions for the food multiprocessor
(1) To chop and mix ingredients (not for making milk shakes):
- Attach the two blade shafts (D) to the two blade supports (G)
in the container (E) and put in the food to be chopped or mixed.
See Figure 1.
- Place the lid (B) on top of the container (E) and place the motor
module (A) on top of the lid opening (C). Plug the appliance in.
Press down on the motor module and press the speed switch
to make the appliance work. Press the speed switch lightly for
slow speeds and firmly for faster speeds.
- The motor module (A) has a built-in protection switch. If the
motor module (A) is not placed correctly on top of the lid ope-
ning (C), the protection lug will not make contact with the pro-
tection switch and the motor module (A) will not work.
- Unplug the appliance after use and wait until the blades (F)
have stopped moving completely. Then remove the motor mo-
dule (A), the lid (B) and the blades (F).
(2) To make milk shakes:
- Attach the shake attachments (H) to the blade shafts (D). See
Figure 2.
- Attach the two blade shafts (D) with the shake attachments
(H) to the two blade supports (G) in the container (E) and put in
the ingredients to be mixed.
- Place the lid (B) on top of the container (E) and place the motor
module (A) on top of the lid opening (C). Plug the appliance in.
Press down on the motor module and press the speed switch
to make the appliance work. Press the speed switch lightly for
slow speeds and firmly for faster speeds.
- Always wait until the blades (F) have completely stopped mo-
ving before removing the shake attachments (H). To remove
them, take off the motor module (A) and the lid (B), place your
index and middle fingers underneath the collar of the shake ac-
cessory (H) and your thumb on the end of the screw, and lift the
collar while keeping your thumb on the screw. See Figure 3.
(D) Cleaning the food multiprocessor
IMPORTANT: Do not immerse the motor module (A) in water
or rinse it under a tap. Do not put it in a dishwasher. To clean it,
use a damp cloth.
IMPORTANT: Take care when cleaning the blades, as they are
very sharp.
Cleaning the food multiprocessor container and attach-
ments
- Unplug the appliance.
- Remove the motor module (A) and the lid (B).
- Take out the blade shafts (D) and the shake attachments (H)
from the container (E).
- Clean the container with soapy water and a cloth or soft spon-
ge. Do not use abrasive chemical cleaning products or scourers,
as they may scratch the plastic.
- Rinse the lid (B), container (E) and attachments with tap
water.
- Allow the attachments to dry.
- Clean the motor module (A) with a damp cloth. Never immer-
se it in water.
- Make sure the appliance is totally dry before using it again.
- Store the appliance in a dry place.
3