Adjusting The Position Of An Existing Start Id; Erasing Start Ids - Sony DTC-A6 Bedienungsanleitung

Writing Sub Codes
Accurate Positioning of Start IDs
(Rehearsal)
1
During playback, press START ID REHEARSAL
when you arrive at the proper position.
"REHRSL" appears, "START ID" flashes in the
display and Rehearsal repeats a 3-second portion
starting from the selected position. Note that the
repeated portion will play back 8 times, with the
remaining number of times appearing to the right
of the "REHRSL". After 8 times, the deck
automatically stops.
2
Press REW 0 or FF ) to move the beginning
of the repeated portion.
Each time you press the REW 0 or FF )
button, the beginning of the repeated portion
shifts backwards or forwards in 0.3-second
increments, up to a maximum extent of about 2
seconds (4 seconds in long-play mode) in either
direction.
Position where the START ID REHEARSAL
button is pressed in Step 1.
↓
Movement
0.3 sec
with each press
of REW 0
The time in the display shows the shift in position from
the time the START ID REHEARSAL button was
pressed.
After pressing
FF ) twice
0 6 .
3
Press WRITE.
"ID WRITE" appears in the display for a few
seconds and the start ID is written on the tape at
the selected position. "START ID" flashes in the
display during this time.
EN
16
3 seconds
Repeated portion
Movement with each press of FF )
0.3 sec
After pressing
REW 0 twice
S 0 6 . S
START ID START ID
Adjusting the Position of an
Existing Start ID
You can adjust the position of previously recorded
start IDs.
TIMER PREVIOUS NEXT REW FF MODE RESET
= + 0 )
REC OFF PLAY AMS
STOP PLAY PAUSE REC MUTE REC
POWER
p ( P R r
1
During playback, press START ID REHEARSAL
when the existing start ID you want to reposition
is displayed.
The deck rewinds to the beginning of start ID and
Rehearsal repeats a 3-second portion.
2
Do Steps 1 to 3 of "Accurate Positioning of Start
IDs (Rehearsal)" on this page.
You can move the start ID to a maximum extent of
about 2 seconds (4 seconds in long-play mode) in
either direction from its original position.
Note
Start IDs written within 10 seconds from the end of the tape
may be difficult or impossible to move.

Erasing Start IDs

You can erase any start ID.
TIMER PREVIOUS NEXT REW FF MODE RESET
= + 0 )
REC OFF PLAY AMS
STOP PLAY PAUSE REC MUTE REC
POWER
p ( P R r
Press ERASE when the start ID you want to erase is
displayed.
"(ERASE)" appears in the display as the deck rewinds
to the beginning of the start ID, then "ID ERASE"
appears as the deck erases the start ID.
• It takes 9 seconds to erase a start ID.
• Program numbers are erased together with start IDs.
REC LEVEL L R
MARGIN START ID
5
RESET AUTO RENUMBER REHEARSAL 4 6
3 7
g 2 8
WRITE ERASE
1 9
0 10
INPUT REC MODE SBM PHONES PHONE LEVEL
STANDARD
ANALOG 48 kHz
OPEN/CLOSE ON
OPTICAL 44.1kHz
§ OFF
COAXIAL LONG
0 10
START ID REHEARSAL
REC LEVEL L R
MARGIN START ID
5
4 6
RESET AUTO RENUMBER REHEARSAL
3 7
g 2 8
WRITE ERASE
1 9
0 10
INPUT REC MODE SBM PHONES PHONE LEVEL
STANDARD
OPEN/CLOSE ANALOG 48 kHz ON
OPTICAL 44.1kHz
§
COAXIAL LONG OFF
0 10
ERASE
3-856-761-11(2)