Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
Multi-Colour Head-Up Display 8.89 cm (3.5")
Item No. 2522233
Operating Instructions for download
Use the link www.conrad.com/downloads (alternatively scan the QR code) to download
the complete operating instructions (or new/current versions if available). Follow the in-
structions on the web page.
Intended use
The product is an on-board diagnostic (OBD) and GPS head-up "HUD" display that projects data onto a vehi-
cle windscreen. Information can be read without the driver needing to look away from their usual viewpoints.
Contact with moisture must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
result in or other hazards. Read the instructions carefully and store them in a safe place. Make this product
available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and prod-
uct names are trademarks of their respective owners. All rights reserved.
Delivery content
•
Head-up display
•
On-board diagnostic cable
•
USB cable
•
Reflective film
Explanation of symbols
The symbol warns of hazards that can lead to personal injury.
The arrow symbol indicates special information and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the appliance from extreme temperatures, strong jolts, high humidity, moisture, flam-
mable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can dam-
age the product.
• Consult an expert when in doubt about the operation, safety or connection of the appliance.
• Maintenance, modifications and repairs must only be completed by a technician or an au-
thorised repair centre.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
• Always observe any local regulations relating to the use of head-up displays.
• The information shown on the head-up display is for reference only. If there is a discrepancy
between the head-up display and the manufacturer vehicle guage clusters, use the vehicle
guage clusters. See "Settings → b) HUD system → Setting 1".
Operating elements
a) Overview
1
4
1 Anti-glare hood
3 Light sensor
2 Display
4 Wave button
•
Non-slip mat
•
Operating instructions
2
3
5
5 Mini USB-B input
b) Display
A
B
A Speed, coolant temperature,
D Icons:
battery voltage, satellite
numbers, driving distance.
B Decorative lights: Push wave
button right to turn off.
C Units of speed
Getting started
Important
•
Vehicles not compatible with OBD-II / EUOBD can only use the GPS system connected via
USB cable.
•
The OBD-II may not function correctly with electric vehicles, diesel engines, pickup trucks, rec-
reational vehicles, and computer modified cars. Use the GPS system connected via USB cable
instead.
•
Use the GPS system connected via USB cable when the voltage is higher than 24 V.
1. Connect the HUD display:
-
: See section "Connection a) OBD system".
-
: See section "Connection a) GPS system".
2. Remove the protective film from the display.
3. Position the HUD on your vehicle dashboard. Use the non-slip mat to keep
it in place.
4. Face the display towards the windscreeen.
5. Power the HUD up by turning the vehicle ignition key.
6. Within (5 s) of HUD flashing, slide the wave button left or right to switch be-
tween OBD and GPS modes.
7. Position the projection on the windscreen.
8. If the image has some ghosting use the reflective film. See section "Pasting the reflective film".
Basic operation
Button descriptions are when the wave button is facing towards the windscreen
•
Within (5 s) of HUD flashing, slide the wave button left or right to switch between OBD and GPS modes.
•
Push right to toggle between highspeed, all, and speed only display modes.
•
Push down to toggle through information such as voltage, coolant temperature, speed, and GPS satellite
numbers.
Attach reflective film
1. Position the projection where you would like it to be.
2. Hold the reflective film flat against the windscreen. Note where the entire projected image is within the
screen.
Experiment with different positions to achieve the best result.
3. Make sure the area is clean, use water and a lint-free cloth to wipe the glass.
4. Spray some water where you intend to attach the screen.
5. Tear off the backing marked "1" then carefully lay it over the glass.
- Adjust the position.
- Use a credit card to gently scrape out any bubbles.
6. Slowly peel off the backing marked "2", taking care not to pull the film away from the glass.
If the projection still does not line up within the screen, try adjusting the HUD.
Connection
a) OBD system
Displayed information includes vehicle speed, engine rpm, engine rpm icon, coolant temperature, driving
distance after the ignition is switched off, battery performance, progress icons.
Important
•
Refer to the vehicle operating instructions for how to connect to the OBD interface
•
To preserve the vehicle battery, disconnect the OBD connector if you do not use it for a few days.
1. Connect the OBD cable to the USB port on the HUD.
2. Connect the OBD cable to the vehicle OBD interface.
Tidy the cable by tucking it under the sealing strip that runs along the A pillar.
3. Turn the ignition key to start the OBS system. It can take up to 1 minute until information is displayed.
C
D
E
E Progress bar
Battery voltage
Engine speed
OBD system
Vehicle speed
GPS system
Coolant temperature
Werbung
