Product Overview; Technical Data - Conrad 2361861 Bedienungsanleitung

6 Product overview

1
2
3
4
5
6
7
1 Cover
3 Reamer (small fruits)
5 Juice collector
7 Base unit with motor
7 Before first use
P :
RECONDITIONS
a
All parts that contact food should be thoroughly cleaned before use. See section "Cleaning and care".
1. Place the product on a dry, level, sturdy, heat resistant surface.
2. Attach the juice collector to the base unit.
à
Align the notches on the bottom of the collector with the base unit.
à Rotate the juice collector clockwise until it "locks" into place.
3. Place the sieve over the top of the collector. It should sit flush.
4. Align the reamer over the motor shaft and insert it all the way down until it sits flush with the sieve.
4
8
2 Reamer (large fruits)
4 Sieve
6 Motor shaft
8 Power plug
8 Juicing
Important:
■
During use, the motor will judder and may change direction of rotation. This is normal.
■
Risk of damage! Never exert excessive force when pressing fruit to prevent choking and
damaging the motor.
■
Risk of overheating! The maximum continuous operating times are: ON 15s, OFF 15s.
After 10 consecutive cycles the appliance must be cooled down for 30 minutes before us-
ing again.
P :
RECONDITIONS
a
Citrus fruits are prepared for juicing e.g., washed and halved.
a
The product is fully assembled and connected to the mains power.
a
The correct size reamer has been selected.
1. Gently press the cut side of the fruit against the reamer.
à
The motor starts when pressure is applied.
à The motor stops when the pressure is removed.
2. Extracted juice will empty into the collector. Empty it before it gets full.
3. Disconnect the product from the power supply after use.
Tips:
■
Wash parts soon after use. This will prevent residue from drying onto parts making it difficult to re-
move later. See section "Cleaning and care".
■
Extract juice more efficiently by pressing the fruit down onto the reamer several times for short
durations.
■
Fruit pulp may accumulate on the reamer or restrict juice from flowing through the sieve. Clear
build up if needed.
9 Cleaning and care
Important:
■
Risk of electric shock! Do not wash the base motor unit under running water or sub-
merge. Always keep electrical connections dry!
■
Always disconnect the appliance from the power supply when not in use e.g., leaving it
without supervision, before assembly, disassembly, or cleaning.
■
Allow the product to completely cool down before cleaning.
■
Parts are not dishwasher safe.
NOTICE! Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
1. Disconnect the product from the power supply.
2. Rinse the cover, reamer, sieve, and juice collector under warm running water. Use a mild kitchen de-
tergent and soft (non-abrasive) sponge if needed.
3. Rinse all the parts under clean running water then dry using a fiber-free cloth.
4. Wipe the base with motor unit using a dry or lightly moistened, fiber-free cloth.
5. Store the product fully assembled.
10 Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.

11 Technical data

Rated input ............................................. 220 – 240 V/AC, 50 Hz
Rated power ........................................... 30 W
Volume.................................................... 0.8 litres
Motor....................................................... 44/20 synchronous
Noise level .............................................. max. 82 dB(A)
Operating interval ................................... [(ON 15 s, OFF 15 s)] x10 consecutive cycles + 30 mins OFF
Protection class ...................................... II
Operating conditions............................... -10 to +50 °C, 40 – 60 % RH (non-condensing)
Storage conditions .................................. -10 to +50 °C, 60 – 80 % RH (non-condensing)
Dimensions (W x H x D).......................... 197 x 218 x 141 mm
Weight (approx.) ..................................... 0.75 kg
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2361861_V1_0721_dh_mh_en