Herunterladen Inhalt Inhalt Diese Seite drucken

Sound Reproduction; Operating Bars - Fast Access To Settings And Functions; Adjusting Colour, Brightness, Contrast Of The Live Images; Recordings - Monacor 18.4510 Bedienungsanleitung

Mehrkanal-hybrid-digital-rekorder zur videoüberwachung
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

7.3.3 Sound reproduction

Only the sound of the camera channel displayed in full-screen
mode, or, in the multi-image mode, only the sound of the
image highlighted by a blue border (to be selected with the
left mouse button) will be reproduced.
1) To adjust the volume, show the toolbar (Fig. 7-10) with the
right mouse button.
2) Click the speaker symbol
appear.
3) Keep the left mouse button pressed and adjust the volume
with the slider.
4) To mute the sound, click the speaker symbol located directly
beneath the slider. Proceed in the same way to unmute
the sound.
To mute and unmute the sound, the button MUTE at the
recorder or on the remote control may be used as well. Please
note that the volume control (slider) must not be shown.
7.4 Operating bars – fast access to settings
and functions
For fast access to the setting menus and the most important
functions, the toolbar (click the right mouse button to show
it) is available; for each camera, the quick-access bar (click the
desired camera image with the left mouse button) is provided.
Fig. 7-10 Toolbar
Symbol Function
To call up the main menu; the following will be selected:
menu "Parameter"
submenu "Display"
section "Analog Channels"
The lock symbol will only be available when the password
feature has been enabled (chapter 6.6).
When the lock is opened, click the lock symbol to enable
the password protection feature (chapter 7.1)
When the lock is closed, the password protection feature
is enabled, click the lock symbol to open the window for
changing the user (chapter 7.2).
View with four camera images
The recorders AXR-108 and AXR-116 provide additional
symbols for a view with 9, 12, (16), (25) images.
View with camera images of different sizes
Stream switch for the camera image highlighted by a blue
border:
"Mainstream" = high resolution, high data volumes
"Substream" = low resolution, low data volumes
The "Preview Policy" defines the priorities to be applied
when system utilization has reached 100%
Realtime = highest frame rate possible, lower image quality
Balanced = medium frame rate, medium image quality
Smooth = highest image quality possible, fewer frames per
second
To start / stop the image sequence (chapter 7.3)
To adjust the volume; to mute and unmute the sound
(chapter 7.3.3)
To open the menu for record search (chapter 7.7.2)
50
. A volume control (slider) will
Fig. 7-11 Quick-selection bar with separate functions
for each camera image
Symbol Function
To save a snapshot (chapter 7.6.2)
To start or stop recording manually (chapter 7.6)
To replay the most recent 5 minutes recorded (chapter 7.7.1)
To magnify an image section (chapter 7.3.2)
To adjust colour, brightness and contrast (chapter 7.5)
To call up the control menu for a PTZ camera (chapter 7.8)
7.5 Adjusting colour, brightness, contrast
of the live images
1) Use the left mouse button to click the live image to be ad-
justed. (In the single-image mode, simply press the left mouse
button.) The quick-selection bar will appear (Fig. 7-11).
2) Click the colour palette symbol
displayed in the single-image mode and the menu for the
image settings will appear:
Color
Channel
CH1
HUE
BRIGHT
CONTRAST
SATURATION
Default
Save
Cancel
Fig. 7-12 Menu for the image settings
Menu item
Function
Channel
To switch to a different camera channel
HUE
To adjust the hue
BRIGHT
To adjust the brightness
CONTRAST
To adjust the contrast
SATURATION
To adjust the saturation
Default
Reset to factory settings
Save
To save the settings
Cancel
To exit the menu
3) To go back to the previous view after the menu was exited,
double-click with the left mouse button.

7.6 Recordings

According to the factory settings, the recorder will, after
it is switched on, record all channels to which a camera is
connected. When this setting has been changed (menu
"Parameter", submenu "Record", section "Record Schedule"),
recording can be manually started for a channel that is not
automatically recorded.
1) Use the left mouse button to click the live image to
be recorded. (In the single-image mode, simply press the
left mouse button.) The quick-selection bar will appear
(Fig. 7-11).
2) Click the camera symbol
afterwards and the symbol
3) To stop recording, click the symbol
As an alternative, use the button
remote control to start recording, and the button ■ to stop
recording. In the multi-image mode, the camera whose image
is highlighted by a blue border will be recorded. If required,
before recording is started, use the numeric keys or the buttons
CH– / CH+ to switch to the full-screen mode.
. The live image will be
125
130
132
100
. Recording will start shortly
R
(Record) will be shown.
again.
at the recorder or on the

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis