Monacor 18.4510 Bedienungsanleitung Seite 41

When the network has been configured, click "Next".
5) The menu for adding IP cameras will appear:
IPC Setup
Channel Edit State IP Adress/Domain
IP CH1
IP CH2
IP CH3
IP CH4
IP CH5
IP CH6
Auto Assign IP to Camera(s) Channel Delete
Total band width:8Mbps, used band width:0bps
Don't show this window next time.
Fig. 6-15 Adding IP cameras
When no IP camera is available, click "Next" to go to the
next menu and continue with step 7.
IP cameras can only be added when they have been
connected to the network (see instruction manual of the
camera). For adding IP cameras, the following options are
available:
Button Function
Click the plus symbol to assign a specific IP cam-
era to a camera channel. The window "Quick
Add" will appear. Click "Search" to show all
IP CH...
cameras available in the network. Click the cam-
era desired to select it and then click "Add".
Auto Assign IP
Automatic assignment
to Camera(s)
To remove a camera
Channel Delete
(click to select the entire line of the camera)
To add cameras to all IP camera channels avail-
Add All
able
User-defined
User-defined adding of cameras
Add
In addition to analog cameras,
2 IP cameras (with recorder AXR-104)
4 IP cameras (with recorder AXR-108)
8 IP cameras (with recorder AXR-116)
can be used. When a channel for an analog camera is
switched off, an additional IP camera can be used instead.
When the IP cameras have been added, click "Next".
6) The menu for automatic recording will appear. According to
the factory settings, all camera channels to which a camera
is connected, will record from 00:00 – 24:00.
Record Schedule
Channel CH1 Normal
0 2 4 6 8 10
S
M
T
W
T
F
S
Copy CH1 To All
Don't show this window next time.
Fig. 6-16 Weekly schedule for recordings
To change the settings:
a) After "Channel", a camera channel is selected (here:
channel 1). To change the recording time for a different
channel, click the symbol
b) To delete recording times, keep the left mouse button
pressed and move the mouse pointer over the time range
desired. Individual half-hour blocks can be deleted by
a simple click.
c) Proceed in the same way to add times that have been
deleted.
d) To automatically start recording when a motion is
detected and/or an alarm is triggered, first click the
Subnet Maske Port M
Add All User-defined Add
×
Cancel Previous Next
Motion Alarm
12 14 16 18 20 22
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Copy
×
Cancel Previous Next

.
yellow ellipse "Motion" or the red ellipse "Alarm". Then
keep the left mouse button pressed and move the mouse
pointer over the time range desired.
e) To use the setting for other camera channels as well,
make the appropriate selection in the line "Copy CH ...
To All" at the bottom of the menu and then click "Copy".
f) If required, the recorder can be easily reset to its factory
settings (chapter 7.10).
When the settings have been made, click "Next".
7) A menu for date, time, menu language and other basic
settings will appear:
System General Configuration
Date 02/18/2017
Time 16:37:47
Date Format MM/ DD/YY
Time Format 24Hour
Language ENGLISH
Video Format PAL
Menu Timeouts 1Min
Mode XVR
Don't show this window next time.
Fig. 6-17 Basic system settings
Menu item Note
Date Always make sure to update the date and the
time so that it will be possible to search record-
Time
ings in specific time ranges.
Date Format —
Time Format 24-hour format or 12-hour format
To select one of the 17 menu languages avail-
Language
able
Colour format of the analog cameras connected:
Video Format
PAL (Europe) or NTSC (USA, Asia)
When there is no user input or user action, the
menu will automatically disappear after
30 seconds, 1, 2, 5 or 10 minutes
Menu Timeouts
OFF = The menu will be shown until it is saved
or cancelled.
DVR = Basic mode when the recorder is not to
be connected to a network: The network
Mode
menus will not be displayed.
XVR = Advanced mode with all network menus.
8) When the settings have been made, click the field "Don't
show this window next time" at the bottom of the menu
to make sure that the wizard will not be called up with
the next switch-on. Then click "Save" to save the settings.
9) The message "Wizard Complete !" will appear. Click "OK"
to confirm.
Wizard Complete !
OK
Fig. 6-18 Message "Wizard Complete !"
10) The most important settings for operating the recorder
have now been made. However, if it is possible to access
the recorder via the Internet, make sure to enable the
password protection feature and to change the password
(see chapter 6.6).
11) Finally, reboot the recorder so that all changes will take
effect (Menu  Shutdown  Reboot).
3 0
×
Cancel Previous Save
41