Seite 1
Montage-Anschluss-Anleitung DUO Relaismodul 230V AC / 8A, uP Art.-Nr. 010121.17 P02321-10-002-05 Anerkennung Änderungen G109011 vorbehalten 2013-04-24...
Montage-Anschluss-Anleitung DUO Relaismodul 230V AC / 8A , uP Anwendung Dieses Modul erweitert die Palette der Schaltmodule. Die Ansteuerung kann z. B. über die Aus- gänge des DUO I/O-Moduls (Art.-Nr. 010120.17) erfolgen. Alternativ kann das Modul auch mit einer beliebigen Spannung (9 V bis 15 V DC) angesteuert werden (s.
Montage-Anschluss-Anleitung DUO Relaismodul 230V AC / 8A, uP Montage Die Sicherheitshinweise auf Seite 2 sind zu beachten! Das Modul ist für den Einbau in handelsübliche uP- und Hohlwanddosen Æ 60 mm vorgesehen. - Modul einbauen: Dosen aus Deutschland (DIN) und Österreich Platinen- halter Bei VdS gemäßer Anwendung muss das Modul mindestens an den beiden Stellen an der...
Montage-Anschluss-Anleitung DUO Relaismodul 230V AC / 8A , uP Anschlussplan Anschlusskabel Ansteuerung Die Sicherheitshinweise auf Seite 2 sind zu beachten! Ö Rel2 Relaiskontakte Rel1 Beachten Sie die maximale Belastbarkeit der Relaisausgänge (siehe "Technische Daten"). ACHTUNG! Ö Das Relais darf nach einmaligem Schalten von Strömen am 230 V AC Netz nicht mehr zum Schalten von kleinen Strömen und Spannungen eingesetzt werden (Kontakt- abbrand).
Montage-Anschluss-Anleitung DUO Relaismodul 230V AC / 8A, uP Endmontage Bei VdS gemäßer Anwendung muss der beigefügte Abdeckrahmen verwendet werden! Nur bei nicht VdS gemäßer Anwendung können Sie anstatt des beigefügten Abdeckrahmens eine Standard-Abdeckung für uP-Dosen verwenden (s. u.). Abdeckrahmen montieren Der Abdeckrahmen besitzt 4 Lichtleiter für die von außen sichtbare LED-Anzeige.
Montage-Anschluss-Anleitung DUO Relaismodul 230V AC / 8A , uP Technische Daten Betriebsnennspannung 12 V DC Betriebsspannungsbereich 9 V bis 15 V DC Stromaufnahme bei U_b=12 V DC 18,3 mA Spulenwiderstand 655 Ohm Relaiskontakte: - Kontaktart Umschaltkontakt, potentialfrei - Max. Schaltstrom 8 A bei 250 V AC / 5 A bei 30 V DC - Max.
Seite 9
Mounting and Connection Instructions DUO Switching Module 230V AC / 8A, f.m. Item no. 010121.17 P02321-10-002-05 approval Subject to change G109011 without notice 2013-04-24...
Mounting and Connection Instructions DUO Switching Module 230V AC / 8A , f.m. Application This module is a further addition to the range of switching modules. Activation can take place, e.g. via the outputs of the DUO I/O module (Art. No. 010120.17). Alternatively, the module can also be activated in the voltage range 9 V to 15 V DC (see below).
Mounting and Connection Instructions DUO Switching Module 230V AC / 8A , f.m. Installation Observe the security notes on Page 10! The module is intended for installation in commercially available flush mounted and cavity wall boxes with 60 mm. Æ - Mount module: German boxes (DIN), Austrian boxes mount...
Mounting and Connection Instructions DUO Switching Module 230V AC / 8A , f.m. Connection diagram Connecting cable Activation Observe the security notes on Page 10! Rel2 Relay contacts Rel1 Observe the max. current load rating of the relay outputs (see "Technical data") ATTENTION! After switching currents (once) at the 230 V AC mains, do not use the relay again for switching low currents and...
Mounting and Connection Instructions DUO Switching Module 230V AC / 8A , f.m. Final assembly For use in compliance with VdS, use the enclosed cover frame! For use not in compliance with VdS, a standard cover for flush mounted boxes can be used instead of the enclosed cover frame (s.
Mounting and Connection Instructions DUO Switching Module 230V AC / 8A , f.m. Technical data Rated operating voltage 12 V DC Operating voltage range 9 V to 15 V DC Current consumption at U_b=12 V DC 18.3 mA Coil resistance 655 Ohm Relay contacts: - Type of contact...