Inhaltsverzeichnis
D
Meßpunkte .................................................................................... 3
Antennenanpassung ..................................................................... 8
Comport setzen .......................................................................... 14
DAA programmieren ........................................................... 19 + 20
Dolby - Abgleich .......................................................................... 29
Ausstattung des Arbeitsplatzes:
1. PC ab Pentium II oder höher
2. "ComServer" Software + Dongletreiber + Lies mich Datei
8 627 003 058 (1 CD-Rom Win95/98 + WinNT)
3. Interface (MAUS-Bus / K-Bus auf RS232 Schnittstelle)
8 627 004 057
4. Steckernetzteil für Interface (12V / 500mA) 8 627 004 061
5. Dongle (Hardware Sicherheitssystem in Verbindung mit dem
MAUS-Bus) 8 627 004 059 (nur für dekodierberechtigte
Servicestellen)
6. Anschlußkabel MAUS-Bus (Lautsprecher-ISO Stecker mit 2
Kontaktnadeln) 8 627 004 042
7. Verbindungskabel RS232 (PC zum Interface) 8 627 004 015
8. Konfigurationsdateien (MAUS-Bus-Kommandos + Servicean-
leitung MAUS) für die F3/T2 Geräte mit der Bestellnummer
8 627 003 072 (1 Diskette MS DOS 3
9. Netzgerät 15 V regelbar, 10 A
(Betriebsspannung service 13,5 V)
10. Meßsender (z.B. Meguro, Leader, Kenwood)
11. Hochohmiges Voltmeter Ri > 10 MΩ
12. Outputmeter; Frequenzzähler; NF-Millivoltmeter; Stereocoder
13. Oszilloskop:
- Empfindlichkeit: 5 mV bis 50 Volt/cm.
- Bandbreite: Gleichspannung bis 50 MHz.
14. Tastköpfe 10:1 und 1:1
15. Schraubendreher / Abgleichstifte (keramisch)
16. Lötstation
Die Ausstattungselemente von Punkt 2 bis 8 können über
unser zentrales Ersatzteillager bestellt werden.
Voraussetzung dafür ist, dass ein entsprechender Service- und
Softwarevertrag mit Blaupunkt abgeschlossen wurde.
Haben Sie dazu Fragen, wenden Sie sich bitte an Ihren
nationalen Servicemanager.
Adresse:
Blaupunkt-Werke GmbH
Zentrales Ersatzteillager
Robert-Bosch-Straße 200
D-31139 Hildesheim
1
/
Zoll)
2
- 2 -
Table of Contents
GB
Main Feature list Funline3 ............................................................ 4
Main Feature list T-Line2 .............................................................. 5
Antenna matching ......................................................................... 8
Programming DAA .............................................................. 19 + 20
Dolby alignment .......................................................................... 29
Work place equipment:
1. Pentium II or higher
2. "ComServer" software + dongle driver + read-me files
8 627 003 058 (1 CD-Rom Win 95/98 + WinNT)
3. Interface (MAUS bus / K-bus to RS232 interface)
8 627 004 057
4. Power adapter for interface (12V / 500mA) 8 627 004 061
5. Dongle (hardware security system in connection with the MAUS
bus) 8 627 004 059 (for authorised decoding agents only)
6. MAUS bus cable (ISO speaker connector with 2 pins)
8 627 004 042
7. Extension cable RS232 (PC to interface) 8 627 004 015
8. Configuration files (MAUS bus commands + service manual
MAUS) for the F3/T2 units with order number 8 627 003 072
(1 MS DOS 3
1
/
inch diskette).
2
9. Power supply unit 15 volts adjustable, 10 A
(Supply voltage service 13.5 V)
10. Signal generator (Meguro, Leader, Kenwood)
11. High impedance voltmeter Ri > 10 MΩ
12. Output meter; frequency counter; AF millivoltmeter; stereo
encoder
13. Oscilloscope: - inp. sensitivity: 5 mV to 50 volts per division
- bandwidth: d.c. to 50 MHz
14. Probes 10:1 and 1:1
15. Screwdriver / adjusting pins (ceramic)
16. Soldering station
The items listed under 2 - 8 are available from our Central
Spare Parts Warehouse.
For this it is necessary that you have entered into a
corresponding service and software agreement with Blau-
punkt. If you should have any questions on this topic, then
please get in touch with your national service manager.
Adress:
Blaupunkt-Werke GmbH
Zentrales Ersatzteillager
Robert-Bosch-Straße 200
D-31139 Hildesheim