Cleaning And Maintenance - Honeywell FH-971E Gebrauchsanweisung

2. When you do not wish use the fan heater,
you must pull the power cable (12) out
completely.
OPERATING INSTRUCTIONS
FH-971E Fan Heater with rotary power switch
FH-972E Fan Heater with rotary thermostat switch
FH-973E Fan Heater with power - / thermostat
rotary switch
1. Make sure that the rotary power switch (3)
is in the OFF position (4). Connect the
power plug to the power socket. Do not
touch the power cable with wet hands.
2. Make sure that the air intake vent (11)
and air exhaust vent (2) are not cov-
ered. The air intake vent (11) and air
exhaust vent (2) must always be free
when the fan heater is operating.
3. Use the rotary power switch (8) and/or the
rotary thermostat switch (8) for the heating
operation, depending on the fan heater
model and as described below.
4. Before you move or store the fan heater,
turn the rotary power switch (3) to the OFF
position (4) and unplug the appliance.
Rotary power switch
1. By turning the rotary power switch (3) in a
clockwise direction you can choose
between 4 possible settings:
(O) OFF (4)
( ) Cold air (5)
( ) Warm air 1000 Watt (6)
( ) Hot air 2000 Watt (7)
2. When the rotary power switch (3) is in the
hot air 2000 W position (7), you cannot
turn it further in a clockwise direction, but
have to turn it back in an anticlockwise
direction.
Rotary thermostat switch
1. For model FH-973E, first turn the rotary
power switch (3) to a heating setting. For
model FH-972E follow the instructions
starting at 2.
2. Turn the rotary power switch (8) clockwise
to the highest position 7.
ENGLISH
3. When the desired room temperature is
reached, turn the rotary thermostat switch
(8) anticlockwise until you hear it click.
Now the fan heater turns the heating
operation off.
4. Now turn the rotary thermostat switch back
(8) clockwise very slightly. The fan heater
will now automatically switch on and off to
maintain the chosen room temperature.
5. The further you turn the rotary thermostat
switch (8) in a clockwise direction, the
higher the room temperature will be. The
highest position 7 corresponds to a room
temperature of about 30°C. The lowest
position ( ) corresponds to a room temper-
ature of about 5 °C.
6. It is normal for the thermostat not to switch
itself on when the room temperature is
more than 30 °C.
7. If the room temperature is less than 5 °C,
the fan heater will heat until the room
temperature has risen to above 5 °C.
8. When the rotary power switch (3) is in the
hot air 2000 W position (7), you cannot
turn it further in a clockwise direction, but
have to turn it in an anticlockwise direction.
Overheating protection
1. The fan heater is equipped with overheat-
ing protection, which automatically switches
the appliance off if it is overheated.
2. In this case, turn the rotary power switch
(3) to the OFF position (4) and unplug the
appliance.
3. Allow the fan heater to cool for at least 20
minutes.
4. If necessary, remove any objects which
have caused faulty operating or overheat-
ing from inside or in front of the air intake
vent (11) or air exhaust vent (2).
5. Restart the fan heater as described in the
„operating instructions".

CLEANING AND MAINTENANCE

We advise you to clean the fan heater regularly.
So as not to impair the working of the fan heater,
please follow the instructions for cleaning and
maintenance.
5