Appliance Description; Operation; User Interface Description; Switching The Appliance On - AEG BHG 1000W Bedienung Und Installation

Operation - for users and contractors

3. Appliance description

This appliance has been designed as a booster heater
and is particularly suitable for bathrooms, as well as dry-
ing and warming bathrobes and towels. You can place
your towels at various heights.
The appliance heats the room through natural convection
and radiated warmth. The integral room thermostat keeps
the room at the set temperature. For this, it is important
that the appliance's heating output matches the room's
heat demand. This only applies if no towels or bathrobes
are hung on the appliance.
The boost function enables the appliance to be operated
at full heating output without temperature control for a
limited period of 2 hours. You can program the time at
which the appliance starts automatically every day.
The appliance is ready for operation when it has been
fixed to the wall and plugged into the mains.

4. Operation

4.1

User interface description

You operate the appliance by means of its user interface.
1
1 ON/OFF indicator
2 Heat indicator
3 Temperature selector
4 "24h auto" setting range
5 Rotary selector

4.2 Switching the appliance on

» Set the mode selector to "ON".
» Set the required room temperature with the temper-
ature selector. You can choose between 10 °C and
30 °C.
The heat indicator lights up when the appliance starts to
heat. The heat indicator goes off when the temperature
set at the temperature selector is reached.
Note
If several appliances are installed in one room, a
different temperature can be set at each one.
Note
To avoid excessive power consumption when win-
dows are open, stop the appliance while venting.
4.3 2 h boost function
Enable
» Switch the appliance on.
» Press the mode selector for about a second.
The ON/OFF indicator and the heat indicator illuminate.
The appliance heats for 2 hours at full output.
At the end of the 2 hours, the appliance returns to stand-
ard operation with the temperature selector. The heat
indicator and ON/OFF indicator extinguish.
12
2
5 4 3
Disable
» Press the mode selector for about a second.
The heat indicator and ON/OFF indicator extinguish. The
appliance returns to normal operation controlled by the
temperature selector.
4.4 24 h automatic function
The 24 h automatic function repeats the 2 h boost function
automatically every 24 hours.
Enable
Turn the mode selector fully clockwise to "24 h auto".
The ON/OFF indicator and the heat indicator illuminate.
The appliance heats for 2 hours at full output.
At the end of the 2 hours, the appliance returns to stand-
ard operation with the temperature selector. The heat
indicator and ON/OFF indicator extinguish.
The 2h boost function starts the following day 45 minutes
before the time when the appliance was set to "24h auto".
Example:
You would like your bathroom to be at the required tem-
perature at 07:00 h in the morning.
» On the first day at 07:00 h in the morning, set the ro-
tary selector to "24h auto".
The appliance immediately starts heating as per the 2 h
boost function. The next day, the 2h boost function auto-
matically starts at 06:15 h in the morning, in order to heat
up the bathroom for 07:00 h.
Interruption
You can interrupt the 2 h boost function at any time with-
out changing the start time.
» Press the mode selector for about a second.
The heat indicator and ON/OFF indicator extinguish. The
appliance returns to normal operation controlled by the
temperature selector.
On the following day the 2 h boost function will resume
from the usual start time.
Disable
» Turn the mode selector fully anti-clockwise to "ON".
The heat indicator and ON/OFF indicator extinguish. The
appliance returns to normal operation controlled by the
temperature selector.

4.5 Childproofing

This function prevents the temperature setting from being
changed unintentionally.
If the childproof setting is active, the temperature and
mode selectors are not operational. The ON/OFF indica-
tor flashes if you adjust the mode selector/temperature
selector.
Enable
» Press and hold the mode selector for more than
three seconds.
The ON/OFF indicator flashes consecutively five times.
This tells you that the childproof setting is active.
You can also use the 2 h boost function as usual when
childproofing has been enabled.
Disable
» Press and hold the mode selector for more than
three seconds.
The ON/OFF indicator flashes consecutively five times.
This tells you that the childproof setting is disabled.