Electrical Connection; Cleaning, Maintenance, And Storage; Transport - Parkside PBS 350 A1 Originalbetriebsanleitung

11.2 Performing angled cuts (Fig. 17)
• Set saw bench to desired angle (see 10.3).
• Perform the cut as described under 11.1.
When producing angled cuts, only use the parallel stop to the
right of the saw band.
11.3 Freehand cuts (Fig. 19)
• One of the most important features of a band saw is the ease
with which it can cut curves and radii.
• Lower the saw band guide (5) onto the workpiece (see 9.5).
• Switch on the saw.
• Press the workpiece firmly onto the saw bench (7) and slow-
ly slide into the bandsaw blade (21).
• In many cases it is helpful to roughly saw curves and corners
approximately 6 mm from the line.
• If it is necessary to saw curves that are too tight for the saw
band used, auxiliary cuts must be sawn up to the front face
of the curve, so that these fall off as wood waste when the
final radius is sawn.

12. Electrical connection

The electrical motor installed is connected and ready for op-
eration. The connection complies with the applicable VDE and
DIN provisions.
The customer's mains connection as well as the extension cable
used must also comply with these regulations.
Important information
In the event of an overloading the motor will switch itself off. Af-
ter a cool-down period (time varies) the motor can be switched
back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Passage points, where connection cables are passed through
windows or doors.
• Kinks where the connection cable has been improperly fas-
tened or routed.
• Places where the connection cables have been cut due to
being driven over.
• Insulation damage due to being ripped out of the wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be used
and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regularly.
Make sure that the connection cable does not hang on the
power network during the inspection.
Electrical connection cables must comply with the applicable
VDE and DIN provisions. Only use connection cables with the
marking „H05VV-F".
The printing of the type designation on the connection cable
is mandatory.
AC motor:
• The mains voltage must be 230 - 240 V∼ 50 Hz.
• Extension cables up to 25 m long must have a cross-section
of 1.5 mm .
2
10 GB/IE/NI
Connections and repairs of electrical equipment may only be
carried out by an electrician.
Please provide the following information in the
event of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate

13. Cleaning, maintenance, and storage

m Important!
Prior to any adjustment, maintenance or service work discon-
nect the mains power plug!
Cleaning
Keep all safety devices, air vents and the motor housing free
of dirt and dust as far as possible. Wipe the equipment with
a clean cloth or blow it with compressed air at low pressure.
We recommend that you clean the device immediately each
time you have finished using it.
Maintenance
There are no parts inside the equipment which require addi-
tional maintenance.
Storage
Store the device and its accessories in a dark, dry and frost-
proof place that is inaccessible to children. The optimum stor-
age temperature is between 5 and 30˚C.
Store the power tool in original packaging.
Cover the electrical tool in order to protect it from dust and
moisture.
Store the operating manual with the electrical tool.
Service information
Please note that the following parts of this product are sub-
ject to normal or natural wear and that the following parts are
therefore also required for use as consumables.
Wear parts*: bandsaw blade, table inserts, Push stick
* Not necessarily included in the scope of delivery!

14. Transport

The machine must only be lifted and transported on its frame
or the frame plate. Never lift the machine at the safety devices,
the adjusting levers, or the sawing table.
During the transport the saw blade protection must be in the
lowest position and near the table.
Never raise at the table! Unplug the machine from the mains
during transport.