Herunterladen Diese Seite drucken

Blaupunkt gta 470 Einbauanleitung Und Bedienungsanleitung Seite 3

Vorschau ausblenden Andere Handbücher für gta 470:

Werbung

Hierzu noch einige wichtige Erläuterungen:
Durch Drehen des Reglers im Uhrzeiger-sinn erhöht
sich die Eingangsempfindlichkeit des Verstärkers und
damit auch die Lautstärke. Es handelt sich jedoch
nicht um eine Lautstärkeregelung; in der Endposition
läßt sich keine höhere Verstärkerleistung erzielen,
auch wenn sich dies zunächst so anhört. Das Sy-
stem steigert lediglich schneller die Lautstärke, wenn
die Lautstärkeregelung des Radiogerätes aufgedreht
wird.
Lautsprecheranschlüsse
(Falls der Verstärker in Brücke geschaltet werden soll,
an dieser Stelle direkt mit dem Abschnitt „Überbrückte
Lautsprecheranschlüsse" fortfahren).
Wie bei jeder Audiokomponente ist die korrekte
Polung von Verstärker und Lautsprechern von es-
sentieller Bedeutung für eine gute Basswiedergabe.
Deshalb ist bei den Anschlüssen darauf zu achten,
dass der positive (+) Anschluss des Verstärkers mit
dem positiven Anschluss (+) des Lautsprechers ver-
bunden wird; entsprechendes gilt für die negativen (-
) Anschlüsse. Außerdem muss der linke Verstärker-
kanal mit dem linken Lautsprecher und der rechte
Verstärkerkanal mit dem rechten Lautsprecher ver-
bunden werden.
Überbrückte Lautsprecheranschlüsse
Der GTA-Verstärker kann für eine Monokonfiguration
auch in Brücke geschaltet werden. Auf diese Weise
kann der Verstärker für einen oder mehrere
Subwoofer bzw. einen Mitteltöner verwendet werden.
In dieser Konfiguration addiert der Verstärker den
rechten und linken Kanal zu einem Einkanalausgang
(Monoausgang).
Hinweis:
Der Verstärker kann die rechte und linke Signal-
information nur dann addieren, wenn sowohl der rech-
te als auch der linke RCA-Anschluss vorgenommen
wurde.
Achtung:
In Brückenschaltung muss die Verstärkerlast 4
Ohm oder höher betragen. Eine niedrigere Last
führt zu einer Überhitzung oder Abschaltung des
Verstärkers und kann dauerhafte Schäden verur-
sachen.
Art und Bereich der Frequenzübergänge
einstellen.
Beim GTA 470 kann die Art des Frequenzübergangs
(d. h. „Low-Pass" oder „Hi-Pass") und die gewünschte
Einstiegsfrequenz eingestellt werden. Wenn bei-
spielsweise ein Subwoofer- Paar angeschlossen
werden soll, sind die abgebildeten „Low-Pass"- Ein-
stellungen erforderlich (Fig. 3). Die Einstiegsfrequenz
ist abhängig vom Frequenzbereich der Lautsprecher
(siehe empfohlener Frequenzbereich der Lautspre-
cher).
„High- Pass"
Bei der Einstellung von 250 Hz hat der Verstärker
einen Frequenzbereich von 250 Hz bis 26.000 Hz.
„Low- Pass"- Frequenzregelung
Dieser Regler ist aktiv, wenn sich der Schalter in der
Position „Low-Pass" befindet, und ermöglicht die Ein-
stellung der gewünschten Einstiegsfrequenz. Bei-
spiel: Bei einer Einstellung von 150 Hz hat der Ver-
stärker einen Frequenzbereich von 10 Hz bis 150
Hz.
Bass Boost
Mit Hilfe des Bass Boost Reglers kann die
Basswiedergabe des Verstärkers eingestellt werden.
Der Einstellbereich reicht von 0 dB bis +12 dB.
Betriebsanzeige
(POWER / PROTECTION)
Grünes Licht: Endstufe an, regulärer Betriebszustand.
Rotes Licht: Endstufe ist elektronisch abgeschaltet
da Fehlerfall vorliegt.
Änderungen vorbehalten!
ENGLISH
Introduction
Congratulations on your purchase of a high-quality
GTA power amplifier. By selecting the GTA 470 you
have chosen a product which delivers superlative
reproduction quality. Whether you are upgrading an
existing system or using the GTA power amplifier in
a new system, you are certain to notice immediate
performance benefits!
The Blaupunkt editors are constantly working on
making the operating instructions clearer and easier
to understand. However, if you still have any questions
on how to operate the equipment, please contact your
dealer or the telephone hotline for your country. You
will find the hotline telephone numbers printed at the
back of this booklet.
We provide a manufacturer guarantee for our
products bought within the European Union. You can
view the guarantee conditions at www.blaupunkt.de
or ask for them directly at:
Blaupunkt GmbH
Hotline
Robert Bosch Str. 200
D-31139 Hildesheim
Germany
Recommendation:
A power amplifier's performance is only as good as
its installation. Proper installation will maximise the
overall performance of your audio system. We
recommend that you have our product installed
professionally. Should you decide to install the
amplifier yourself, however, please read through these
instructions carefully, and take your time over the
installation.
Finally, a word about your health: please bear in mind
when playing music in your car that sustained sound
levels above 100 dB can damage your hearing and
may even result in total hearing loss. Modern high-
performance systems and high-quality loudspeaker
configurations are quite capable of generating noise
levels above 130 dB
Safety precautions
Instructions for installation and
connection
Fit a fuse in the amplifier power line no more than 30
cm from the vehicle battery, in order to protect the
battery in the event of a short-circuit between it and
the power amplifier. The amplifier's own fuse protects
the amplifier itself, but not the car battery. Disconnect
the negative terminal of the battery before
carrying out installation and connection work.
Observe the vehicle manufacturer's safety
instructions (regarding airbags, alarm systems, trip
computers, vehicle immobilisers).
The final stage must be installed professionally
for reasons of safety. The mounting surface must
be suitable for the screws provided, and must
provide firm support. For safety reasons the GTA
470 should be fixed in a reliable way. You must
not install the GTA 470 on the rear shelf, on the
rear seats or on any other surface open to the
front.
When drilling holes, take care to avoid damage to
vehicle components (battery, cables, fuse boxes).
Fit the amplifier in a suitable location, e.g. beneath
the seats or in the trunk (Fig. 1). The mounting location
must also be dry, and provide sufficient ventilation
for cooling of the amplifier. Use cable grommets when
passing cables through holes with sharp edges. Use
loudspeakers
with
an
impedance
2 to 4
(see table or installation drawing). Observe
the max. power handling specifications (music
output). Do not connect the loudspeakers to ground;
only use the terminals provided. The cross-section
of the positive and negative cable must be at least
6 mm
2
.
GTA 470 amplifier
The amplifier is suitable for connection to car radios
with Cinch connector. Use the Blaupunkt ISO Cinch
adapter to connect the amplifier to car radios with
ISO connector (7 607 893 093/ 7 607 855 094).
Applications and loudspeaker connection
Quadro-Mode
Max Power
4 x 150 Watt /4Ω
Stereo-Mode
Max Power
2 x 400 Watt /4Ω
Quadro-Mode
Max Power
4 x 200 Watt /2Ω
Quadro-Mode
RMS Power
4 x 70 Watt /4Ω
Stereo-Mode
RMS Power
2 x 200 Watt /4Ω
Quadro-Mode
RMS Power
4 x 100 Watt /2Ω
Frequency
response
10 Hz - 26.000 Hz
Signal-to-noise ratio > 90 dB
Distortion
factor (RMS)
< 0,04%
Stability
2 Ω
Input-sensitivity
0,3 - 8 V
Low-pass filter
50-250 Hz
High-pass filter
50-250 Hz
Bass Boost
0-12 dB
Dimensions
W x H x D (mm)
290 x 49 x 254
Positive/negative connection
We recommend a cable cross-section of not less than
6 mm
2
. Run a standard commercial positive cable to
the battery and connect to the fuse holder. Use cable
grommets when passing cables through holes with
sharp edges. Bolt a standard commercial negative
cable to a ground point free of induced noise (car
body bolt, body panel) - not to the negative battery
pole. Clean the contact surface of the ground point
down to bare metal and coat with antiseize graphite
petroleum.
Integral fuses
The integral fuses within the amplifier protect the fi-
of
GTA 470
Fig. 4, 4a
Fig. 5
Fig. 4, 4a
Fig. 4, 4a
Fig. 5
Fig. 4, 4a
3

Werbung

loading