Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ATS-85PS
Order No. 0179470
ATS-825C
Order No. 0179450
ATS-850PS
Order No. 0179460
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
Charging Station / Charging Case
for Receivers ATS-80R
and Transmitters ATS-80T
These operating instructions are intended for
users without any specific technical knowl-
edge. Please read the instructions carefully
prior to operation and keep them for later
reference.
1 Applications
The charging stations ATS-85PS and ATS-850PS
and the charging case ATS-825C are used for
charging the NiMH batteries of the transmitters
ATS-80T and the receivers ATS-80R. Furthermore,
it is possible to set all transmitters and receivers
to the desired transmission channel at the same
time when a button is pressed. Via the USB port,
all other settings possible can be made by means
of a computer and the software provided.
2 Safety Notes
The product corresponds to all relevant directives
of the EU and is therefore marked with
WARNING The charging station ATS-850PS and
the power supply unit of ATS-85PS
and ATS-825C use dangerous mains
voltage. Leave servicing to skilled
personnel only. Inexpert handling
may result in electric shock.
•
Only use this product for charging NiMH bat-
teries. Non-rechargeable batteries may leak or
even explode if you try to charge them!
•
The product is suitable for indoor use only. Pro-
tect it against dripping water, splash water and
high air humidity. The admissible ambient tem-
perature range is 0 – 40 °C.
•
Do not place any vessel filled with liquid on the
product, e. g. a drinking glass.
•
Do not operate this product and immediately
disconnect the mains plug from the socket
1. if a device or the mains cable is visibly dam-
aged,
2. if a defect might have occurred after a device
was dropped or suffered a similar accident,
3. if malfunctions occur.
Any repairs must be carried out by specialists.
•
Never pull the mains cable to disconnect the
mains plug from the socket, always seize the
plug.
•
For cleaning the product only use a dry, soft
cloth; never use water or chemicals.
•
No guarantee claims for the product and no
liability for any resulting personal damage or
material damage will be accepted if the prod-
uct is not correctly used or not expertly repaired.
If the product is to be put out of opera-
tion definitely, dispose of the product in
accordance with local regulations.
ELECTRONICS FOR SPECIALISTS
01
CHANNEL
PROGRAM
3 Before Operation
Charging station ATS-85PS
Connect the power supply unit to the jack "DC IN
12V". A strain relief clamp next to the jack can be
used to prevent accidental disconnection of the
connection cable. Connect the power supply unit
to a mains socket (230 V/ 50 Hz) using the mains
cable provided.
Charging case ATS-825C
Open the cover of the charging case. Remove the
cover, if necessary: Pull the cover to the left to take
it off its hinges. Connect the power supply unit
to the jack "DC IN 12V" and to a mains socket
(230 V/ 50 Hz) using the mains cable provided.
Charging station ATS-850PS
Either insert the charging station into a rack
.
(482 mm / 19") or use it as a stand-alone device.
Connect the mains jack on the rear to a mains
socket (230 V/ 50 Hz) using the mains cable pro-
vided. The charging station features two mains
switches. It is recommended to always keep the
switch on the rear in the "ON" position; this will
allow you to easily switch on and off the charging
station by means of the switch on the front.
The jack "OUTPUT" on the rear is designed
for connecting a second charging station ATS-
850PS via a suitable mains cable. The second
charging station will be supplied with power via
the first charging station. Thus, a maximum of
four ATS-850PS can be connected in a chain.
3.1 Charging batteries
IMPORTANT! Do not cover the air vents and make
sure that the cover of the charging case ATS-825C
is open while batteries are being charged; other-
wise, the transmitters /receivers inserted and the
charging section may be damaged by heat accu-
mulation.
1) Use the switch
station / charging case.
Note: The charging station /charging case will go into
power-saving mode after 10 minutes when the charg-
ing slots are empty. The LED of the on /off switch
start flashing. To leave the power-saving mode, press
one of the control buttons (<, >,
2) Insert the transmitters and receivers into the
charging slots. The charging status LEDs of the
slots used will light up:
red =
The batteries are being charged.
green =
The batteries have been fully charged
and the transmitter / receiver can be
removed from the charging slot.
flashing = charging error, e. g. batteries have
been inserted the wrong way or
other types of batteries than NiMH
batteries are used
3) When charging is completed, use the switch
to switch off the charging station / charging
case. For models with a power supply unit:
Disconnect the mains plug from the socket to
save power.
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
by MONACOR INTERNATIONAL. All rights reserved.
©
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
Control panel with
USB port, display
and control buttons
to switch on the charging
will
, see figure above).
ELECTRONICS
3.2 Setting the transmission channel
It is possible to set all transmitters and receivers
inserted into the charging slots to the desired
transmission channel at the same time when a
button is pressed:
1) In the control panel (see figure), use the button
< or > to set the transmission channel.
2) Press the button
. The display will indicate
SYNC... while the setting is made. The charg-
ing status LEDs of the slots will go out; the sta-
tus LEDs of the transmitters / receivers inserted
will light up in blue.
3) As soon as the display indicates the channel
number again, the setting has been made.
3.3 Settings via software
To make additional settings for the transmitters /
receivers inserted, install the software "System
Compiler OSW" from the CD provided on a com-
puter with Windows 10 (or later versions of the
operating system). Always proceed in the follow-
ing order:
1) Install the software.
2) Start the software.
3) Connect the computer to the USB port in the
control panel of the charging station / charg-
ing case using the USB cable provided. After
successful connection, the display will indicate
USB.
Four menu pages will show the options for mak-
ing settings via software:
Page 1: joint settings for the transmitters and the
receivers; to select or deselect transmission
channels, load the frequency table "OSW-
DATA-C411.dt" from the CD provided (click
the button "Open File").
Page 2: settings for receivers only
Page 3: settings for transmitters only
Page 4: This page is not required here; it is used
for ATS-80ST only.
Click the button "Update Device" to transmit the
settings to the transmitters and the receivers. The
CD provided contains a PDF file with detailed in-
structions in English.
Windows is a registered trademark of Microsoft Corporation in
the USA and other countries.
4 Specifications
ATS-85PS
ATS-825C
Number of
5
25
charging slots
4 – 6 hours for 1600 mAh batteries
Charging time
(depending on battery status)
Fan
—
⎓ 12 V via
Power supply
power supply unit provided
Ambient
0 – 40 °C
temperature
Dimensions
94 × 65 ×
440 × 175 ×
(W × H × D)
230 mm
275 mm
Weight
750 g
5.2 kg
Subject to technical modification.
A-2042.99.01.02.2020
ATS-850PS
50
yes
100 – 240 V/
50 – 60 Hz/
580 VA
482 × 399 ×
223 mm
12 kg
Werbung
