Herunterladen Inhalt Inhalt Diese Seite drucken

Beko BEKOMAT 3 E 25 Installation Und Betriebsanleitung Seite 5

Vorschau ausblenden Andere Handbücher für BEKOMAT 3 E 25:
Inhaltsverzeichnis

Werbung

deutsch
Alle BEKOMAT 3 und BEKOMAT 6 sind mit einer Zweipunkt-
messung ausgestattet. Die Funktionsbeschreibung des BE-
KOMAT mit Zweipunktmessung wird anhand des BEKOMAT
3 veranschaulicht.
Ventil geschlossen
Kondensat tropft durch die Eintrittsöffnung (1) und sammelt
sich im Behälter (2). Das Membranventil ist geschlossen, da
über die Vorsteuerleitung (3) und das Magnetventil (4) ein
Druckausgleich über der Ventilmembrane (5) erfolgt. Die
größere Fläche oberhalb der Membrane bewirkt eine hohe
Schließkraft. Der Ventilsitz bleibt leckfrei verschlossen.
Ventil offen
Hat sich der Behälter (2) mit Kondensat gefüllt, so dass der
kapazitive Niveausensor (6) am Maximumpunkt ein Signal
meldet, wird das Magnetventil umgeschaltet und der Bereich
oberhalb der Ventilmembrane entlüftet. Die Ventilmembrane
hebt sich vom Ventilsitz (8) ab, und der Überdruck im Gehäuse
drückt das Kondensat in die Auslaufleitung (9).
Die BEKOMAT-Elektronik ermittelt nun die Absinkgeschwin-
digkeit bis zum Minimumpunkt und errechnet daraus exakt die
maximal notwendige Ventilöffnungszeit.
Das Ventil wird rechtzeitig leckfrei verschlossen, bevor es zum
Druckluft-austritt kommt.
Die Austrittsschleuse (10) sorgt dafür, dass sehr grober Schmutz
am Boden des Behälters liegen bleibt.
Bei gestörtem Kondensatabfluss (verstopfte Ablaufleitung,
defekte Membrane) geht das Gerät nach 60 Sekunden in die
Alarmsteuerung. Die rote Leuchtdiode blinkt, ein potential-
freier Kontakt wird geschaltet. In diesem Zustand wird das
Magnetventil alle 4 Minuten für 7,5 Sekunden geöffnet, um
z.B. eine eventuell verstopfte Ablaufleitung selbsttätig freizu-
bekommen.
Darüber hinaus wird dadurch ein im drucklosen Zustand gefüll-
tes Gerät automatisch wieder entleert, sobald der Mindestdruck
im BEKOMAT erreicht ist.
english
All BEKOMAT 3 and BEKOMAT 6 are equipped with two-position
measurement. The following describes the functional charac-
teristics of the BEKOMAT with two-position measurement as
exemplified by the BEKOMAT 3.
Valve closed
Condensate passes through the inlet opening (1) into the col-
lecting container (2). The diaphragm valve is closed, since the
pilot-supply line (3) and the solenoid valve (4) ensure pressure
compensation above the valve diaphragm (5). The larger space
above the diaphragm results in a high closing force. The valve
seat remains tightly closed without leakage loss.
Valve open
Once the container (2) has filled with condensate, so that the
capacitive level sensor (6) emits a signal at the maximum
point, the solenoid valve is reversed and the air above the
valve diaphragm is expelled. The valve diaphragm lifts off the
valve seat (8) and the over pressure in the housing forces the
condensate into the discharge pipe (9).
The BEKOMAT electronic system now determines the lowering
rate down to the minimum point, and uses this figure for calcu-
lating exactly the maxi-mum necessary valve opening time.
The valve will again be fully closed and leaktight, before any
compressed air can escape.
The outflow barrier (10) ensures that very coarse dirt is trapped
at the bottom of the container.
In the event of no condensate discharge (blocked discharge
pipe, faulty diaphragm), the device will change to the alarm
mode after 60 seconds. In this case, the red LED flashes and
a potential-free contact is activated. While in the alarm mode,
the solenoid valve will open every 4 minutes for a period of 7.5
seconds, so that - for instance - any possible obstructions in
the discharge pipe could be cleared automatically.
This also means that a device filled in an unpressurized state
will automa-tically be emptied, as soon as the pressure within
the BEKOMAT has again risen to the required minimum pres-
sure.
5

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Bekomat 3 e 63Bekomat 6 e 25

Inhaltsverzeichnis