Herunterladen Inhalt Inhalt Diese Seite drucken

Beko BEKOMAT 3 CO LA Installation Und Betriebsanleitung Seite 4

Inhaltsverzeichnis

Werbung

1. Lastbetrieb
BEKOMAT LA:
BEKOMAT LALP:
Das Kondensat sammelt sich im Behälter (1) des BEKOMAT.
Das Membranventil (2) hält die Ablaufleitung (3) leckfrei
verschlossen. Hat sich der Behälter mit Kondensat gefüllt,
gibt der kapazitive Doppelsensor (4) ein Signal an die
elektronische Steuerung. Das Vorsteuerventil schaltet und
entlastet das Membranventil (2); dieses öffnet den Ablauf
(3) zur Kondensatableitung.
Die BEKOMAT-Elektronik ermittelt die Absinkgeschwindig-
keit vom oberen zum unteren Sensorschaltpunkt und er-
rechnet daraus die maximale Ventilöffnungszeit. So schließt
das Ventil nach der BEKOMAT-Entleerung rechtzeitig, bevor
unnötige Druckluftverluste auftreten.
Die Schmutzschleuse (5) sorgt dafür, dass grobe Partikel
am Behälterboden zurückgehalten werden.
Ist der Kondensatabfluss gestört (z.B. verstopfte Ablauflei-
tung oder Überlast), schaltet das Gerät in den
Alarmmodus:
Das Ventil öffnet taktweise, um die Störung automatisch zu
beheben. Ist die Störung nach einer Minute noch vorhanden,
blinkt die rote LED und der potentialfreie Störmeldekontakt
schaltet um. Ab diesem Zeitpunkt öffnet das Ventil alle 4
Minuten für jeweils 7,5 Sekunden, und zwar solange, bis
die Störung behoben ist (selbsttätig oder durch Wartung).
Nach Beseitigung der Störung schaltet der BEKOMAT au-
tomatisch in den Normalmodus zurück.
4
1
4
Funktion / Function
p (ü) > 1,2 bar
p (ü) > 0,4 bar
2
3
1. Operation under load
BEKOMAT LA:
BEKOMAT LALP:
Condensate accumulates in the container (1) of the BEKO-
MAT device. The diaphragm valve (2) keeps the discharge
line (3) closed without leakage.
When the container is filled with condensate, the capacitive
level sensor (4) passes a signal to the electronic control.
The pilot valve is then switched and the diaphragm valve
(2) opens the discharge line (3).
The electronic system of the BEKOMAT now determines the
lowering rate from the upper to the lower switching point and,
accordingly, calculates the maximum valve opening time.
Finally, the valve closes the discharge line early enough to
prevent any unnecessary loss of compressed air.
The outlet dirt collector (5) ensures that coarse dirt is trapped
at the bottom of the container.
Alarmmode:
If the condensate flow is disturbed (e.g., blocked discharge
line or faulty diaphragm), the device will change to the alarm
mode after 60 seconds. The red LED flashes and a potential-
free contact is activated. In this state, the solenoid valve
opens every 4 minutes for a period of 7.5 seconds, which
may, e.g., automatically clear the blocked discharge line.
4
5
BEKOMAT 3 CO LA/LALP, 6CO LA/LALP
p (gauge) > 1,2 bar
p (gauge) > 0.4 bar
2
3

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis