Conrad 19 12 20 Bedienungsanleitung Seite 2

O P E R A T I N G I N S T R U C T I O N S
Digital microscope camera USB
Item-No. 19 12 20
Prescribed Use
The product is designed to transfer recorded images via a USB port to a PC.
Via the integrated lenses particularly small objects/surfaces can be magnified and reproduced.
The power is supplied via a USB port.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Scope of delivery
• Camera with permanently attached USB cable
• Operating Instructions
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
Nor do we assume liability for damage to property or personal injury caused
by improper use or failure to observe the safety instructions. The warranty
will be void in such cases.
The unauthorised conversion and/or modification of the product is inadmissible
because of safety and approval reasons (CE).
The product is not a toy and should be kept out of the reach of children.
Do not carelessly leave the packaging material lying around since it could become
a dangerous plaything for children.
The product should only be used in dry indoor areas, it must not be exposed to
damp or wet.
Handle the product with care; knocks, blows or even a fall from a low height can
damage it.
Never look directly into the LEDs at the front side of the camera, you run the risk to
damage your eyes!
Driver/software installation
• Start up your operating system. Place the CD included in delivery in the corresponding drive
of your computer.
• The software now starts automatically and you can install the drivers/software.
If the CD does not start automatically, you have to start the installation program on the CD
manually.
Follow the instructions of the software.
• After installation of the driver/software connect the USB plug of the camera to a free USB2.0
port of your computer. Windows recognises the new hardware and completes the driver instal-
lation.
• Start the software.
After connection of the camera to the USB port, the LEDs of the camera light up.
In the software an unclear picture will appear (only bright and dark spots, but no
proper picture). This is normal since the optics of the camera can only be sharply
focused on objects that are very near to the camera lens.
Operation
• Move the front side of the camera as close as possible to the desired object (e. g. place the
front side on a daily newspaper). The maximum distance to the object is about 4 cm.
• Adjust the picture until it gets sharp by using the adjustment wheel.
By means of the used optics the picture can be focussed in two magnifying levels
(see technical data section).
Do not overwind the adjustment wheel. Turn the adjustment wheel slowly so that
you can focus the picture exactly.
With reflective surfaces or objects the LED light can cause too bright pictures or
reflections.
• Rotate the camera, if necessary, until the picture is adjusted in accordance with your needs.
• Make sure no objects touch the lens as they might damage it. Do not touch the optics (lens will
get dirty).
Handling
www.conrad.com
Version 05/09
°
Cleaning
If required, clean the optics from dust and dirt. Use an appropriate lens cleaning system e. g. a
clean, soft brush. Do not press on the optics/mechanics of the camera too strongly since it may
be damaged. Furthermore, you may cause scratch marks on the lens.
Disposal
Technical Data
Operating voltage ........................................5V= (via USB interface)
Sensor ..........................................................CMOS, 1280 x 1024 Pixel
USB Connection ..........................................USB2.0
Lighting ........................................................4 white LEDs
Magnification approx. ..................................35x or 150x
Dimensions (ØxL) approx.............................34 x 99mm
Weight approx. ............................................85g
© Copyright 2009 by Conrad Electronic SE.
Operation is only permitted in dry, closed rooms. The product may not become
damp or wet.
Never use the product immediately after it has been brought from a cold into a warm
room. The condensation that forms might destroy your unit.
Allow the product to reach room temperature. This may take several hours.
The housing must not be opened! Any maintenance or repair work must only be car-
ried out by authorised personnel.
The following unfavourable conditions are to be avoided when installing or trans-
porting the product:
- Excessive humidity or damp
- Extreme cold or heat
- Dust or flammable gases, fumes or solvents
- Strong vibrations
- Strong magnetic fields such as those found in the vicinity of machinery or loud-
speakers
When setting up/operating the product, ensure that the cables are not bent, over-
wound or squeezed.
When disposing of an unserviceable product, do so in keeping with the relevant
statutory regulations.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.