Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Contents
GB
1
2
Setting Facilities . . . . . . . . . . . . . . . . . . . . . 12
2.1 Creating or deleting access codes . . . . . . . . . 12
2.2 Setting time and date . . . . . . . . . . . . . . . . . . . 13
3
the Alarm Control System . . . . . . . . . . . . . . 14
3.1 Full activation mode . . . . . . . . . . . . . . . . . . . . 14
3.5 Deactivating the alarm control system . . . . . . 16
4
Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
resetting the alarm . . . . . . . . . . . . . . . . . . . . . 16
4.1.1 Reset in case of tampering actions . . . . . . 16
(Tamper Reset) . . . . . . . . . . . . . . . . . . . . . . 16
4.1.2 Reset in case of alarm (Alarm Reset) . . . . . 16
in the display . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.3 Reading the log . . . . . . . . . . . . . . . . . . . . . . . 17
5
Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
system parameters adjusted . . . . . . . . . . . 39
The system is operated via one of the keypad con-
trollers connected.
1 Overview of the Individual Alarm Zones
At the end of these operating instructions you will find
a table which allows you or your system technician to
enter information on the individual zones and on the
parameters adjusted of the alarm control system.
Thus, this important information will always be avail-
able.
As an explanation: In connection with the alarm
control system DA-8000 the term "alarm zone" does
not always mean a certain local area which is moni-
tored by a group of alarm sensors. This is only the case
if the alarm system has thus been equipped. The alarm
sensors which have the same function may be con-
nected together to one of the eight possible zones of
the DA-8000. (A zone is also called line or loop, de-
rived from the electrical way of function.)
Example: All window contacts on the ground floor
are connected to the zone 1 and all motion detectors
on the ground floor to zone 2. The zone 2 has been
programmed with the feature "Part 2". Then the alarm
control system triggers an alarm in the partial activa-
tion mode "Part 2" when one of the windows is opened,
however, it ignores the motion detectors. Thus, the
cleaning personnel will be able to clean the ground
floor without triggering an alarm. However, the alarm
control system already monitors the windows. (In the
partial activation mode "Part 2" all zones with the fea-
ture "Part 2" are excluded from an alarm triggering,
however, not in the full activation mode.)
12
All manuals and user guides at all-guides.com
2 Setting Facilities
A sheet with an overview of the user menu is supplied
with the operating instructions. If you are already quite
familiar with the alarm control system, you may also
make all settings by means of this overview.
2.1 Creating or deleting access codes
To be able to operate the alarm control system, an ac-
cess code is required. Thus, tampering actions by unau-
thorized persons are prevented. Up to nine codes with
three different access authorizations can be created:
User numbers 1 to 3 with all access authorizations
(master access codes)
allows activation, deactivation, and adjusting of
different system parameters (setting the time,
creating access codes, etc.).
User numbers 4 to 7
to activate and deactivate
User numbers 8 to 9
to activate only
The user number 1 with the access code 5, 6, 7, 8 is
factory-set. This can be changed and further user
numbers can be created:
1) The alarm control system must be deactivated and
the display must show <<< UNSET >>>.
01 Jan 00:00
<<<
UNSET
2) Enter a valid master access code with the numeri-
cal keys (e. g. that of the default setting 5, 6, 7, 8).
The display shows:
Do You Want to..
Set User 1 ?
3) Press the button No within 15 seconds, otherwise
the menu will be exited. The display shows:
Do You Want to..
T e s t ?
4) Press the button No again. The display shows:
Do You Want to..
Delete Zone ?
5) Press the button No once more. The display
shows:
Do You Want to..
Select Options ?
6) Press the button Yes. The display shows:
Do You Want to..
Program Chime ?
7) Press the button No again. The display shows:
Do You Want to..
Program Codes ?
8) Press the button Yes. The display shows:
Select
>>>
1..9
Werbung
Kapitel
Inhaltsverzeichnis
