YATO YG-04700 Originalanleitung Seite 8

GB
Recommendations for usage of the product
WARNING! In the case of heating surface cracks you should immediately disconnect the equipment from the power source.
Vessels, which have been made of aluminum foil or plastic, should not be placed on hot surfaces. Any items should not be left
on these surfaces.
Do not place metal objects such as kitchen vessels, cutlery, etc., they should not be placed on the surface of the heating plate,
because they can get hot.
Users, who are wearing rings, watches and similar items should be careful, because they can become hot, If they are near the
surface of induction cooker.
Use only the vessels of recommended types and recommended dimensions. Vessels, which are intended for use in the induction
cookers, should be made of ferromagnetic materials such steel, cast iron, enamelled cast iron and stainless steel intended for
use with the induction cookers. Typically, these vessels are marked with the proper symbol. If you are unsure, please contact the
vessel manufacturer.
Dishes made of diamagnetycznych materials such as: aluminium, copper, glass, including the heat resistant glass, and ceramic
materials, may not be used on an induction cooker, unless they are equipped with a ferromagnetic insert and have proper marking.
Vessels intended for use on an induction cooker must have a flat bottom of suitable diameter. The vessels with a rounded bottom
can not be used on an induction cooker, even if they are made of ferromagnetic materials. Sizes of the vessels, which can be used
on an induction cooker, have been listed in the table of technical data. Do not use vessels with a bottom equipped with footers.
Do not place empty vessels on the cooker. Vessel and cooker can be damaged if you try to heat the empty vessel.
The operation principle of an induction cooker is based on emission of a variable electromagnetic field. People with pacemakers
should avoid handling the induction cooker and staying near the cooker during its work.
WARNING! The surface of the heating plate may be hot after use. Do not touch it because it can cause serious burns. Wait till
the heating plate is cooled down.
In the case of preparation of dishes, that during this operation, may scatter around hot portions of food, you should use personal
protective equipment to prevent burns.
Make sure, that the floor near the cooker is not slippery. This will allow you to prevent slips, which can cause severe injuries.
PRODUCT SERVICE
Installation, starting and operation of the product
You should unpack the product, completely remove all the elements of the packaging; it is recommended that you keep the pack-
aging, it may be useful for later transport and storage of the product.
Wash the product in accordance with the instructions from the point "Product maintenance".
Put on the product an appropriate, filled vessel.
The heating plate is equipped with a sensor that allows you to run the product in the absence of the dish on a plate or when the
vessel bottom has a smaller diameter than these, which is specified in the technical data table.
Make sure, that the knob is in the "off" position. and then insert the plug of product to the mains wall socket.
By using the knob you should set the power range within the range, which is specified in the table.
After work completion you should turn off the cooker by setting the knob to its position "ON/OFF", and then remove the vessel
from cooker.
WARNING! When you remove the vessel from cooker you should be very careful. The vessel and cooker plate can are very hot
and can cause serious burns. Use personal protective equipment in the form of gloves and protective clothing.
You should allow the cooker plate to cool down spontaneously, and then proceed to maintenance as described in section " Product
maintenance"
ATTENTION! The cooker will turn off automatically after two hours since the last time of power change with its knob.
Maintenance of the product
ATTENTION! All maintenance operations must be carried out when the product power supply is turned off. To do this you should
remove the power cord plug from a mains outlet.
Heating plate and other parts of the product should be cleaned by using a cloth soaked in water solution of mild dishwasher liquid.
After the cleaning, you should wipe dry the product. The plate should be cleaned after each use, after it completely cools down.
You should clear all food remains, which have been left on the plate, this will prevent their overcooking during subsequent use,
this will also prevent the performance degradation of product.
For cleaning do not use solvents, aggressive agents, the alcohol gasoline, or abrasive cleaners.
Vents should be cleaned by using a vacuum cleaner.
Attention! Never immerse the product in water or any other liquid.
Storage of the product
If the product will not be used for an extended period of time, you should disconnect it from power supply.
Store the product indoors, protect against dust, dirt and moisture. It is recommended to store the product in the factory packaging.
Store the product in its working position. Do not install the products in layers. Do not place anything on the product during its
storage.
O R I G I N A L I N S T R U C T I O N S
8