Securing/Attaching The Carrying Harness; Fitting The Hedge Trimmer; Removing The Hedge Trimmer; Swivelling The Hedge Trimmer - Parkside PBK 4 A2 Originalbetriebsanleitung

Securing/attaching the carrying harness

♦ Hook the carrying harness
♦ Adjust the carrying harness
is at hip height when the strap is hooked in place.

Fitting the hedge trimmer

♦ First, undo the locking screw
♦ Push the pin on the front boom
on the boom on the engine unit as far as the stop.
You have to make sure that the spring-loaded ball engages in the hole
provided.
♦ Tighten the locking screw
NOTE
► The assembly for the pole pruner/strimmer/3-tooth cutting blade/
extension attachment is done in the same order.

Removing the hedge trimmer

♦ Undo the locking screw and pull the front boom
trimmer out of the boom on the engine unit.
NOTE
► Dismantling the pole pruner/strimmer/3-tooth cutting blade/exten-
sion attachment is done in the same order.

Swivelling the hedge trimmer

♦ Release the lock/release .
♦ Press the control lever and swivel the hedge trimmer into the
desired position.
WARNING!
► The cutter bar must not be pivoted completely backwards parallel
to the front boom in order to work with it.
There is a risk of injury! This position only serves as a transport
position.
♦ Allow the control lever to click into the recess in the base plate
(hedge trimmer) .

Mounting the saw chain and blade

WARNING!
► Wear protective gloves! There is a risk of injury from the sharp cutting
teeth.
NOTE
► Pay close attention to the running direction of the saw chain
the blade and at the base plate (hedge trimmer)
► Depending on wear, the blade
♦ Undo the nut using the spark plug wrench
♦ Remove the sprocket cover
♦ Place the saw chain around the blade
♦ Now fit the blade and saw chain
♦ Lay the guide rail over the blade guide
tensioner pin in the blade hole
chain over the chain sprocket
♦ Now you can tighten the saw chain
checking the saw chain").
♦ Replace the sprocket cover
│ GB │ CY
■ 10
into the carrying lug .
to your size so that the carrying lug
on the boom of the engine unit.
of the hedge trimmer into the opening
.
of the hedge
can be turned.
.
.
starting at the tip.
.
, while inserting the chain
. At the same time, lay the saw
.
(see section "Tightening and
and tighten the nut firmly.

Removing the saw chain

♦ You may have to loosen the saw chain
and the saw chain
saw chain"). Follow these instructions in reverse order.

Tightening and checking the saw chain

WARNING!
► Wear protective gloves! There is a risk of injury from the sharp cutting
teeth.
♦ Turn the chain tensioning screw
screwdriver to increase the tension.
♦ The saw chain
whether the saw chain
NOTE
► A new saw chain

Chain lubrication

♦ Remove the oil filler cap
♦ Fill the oil tank
♦ The chain lubrication can be increased or decreased using the oil
adjusting screw
♦ Press and then turn the oil adjusting screw
the chain lubrication.
♦ Press and then turn the oil adjusting screw
the chain lubrication.
WARNING!
► Never work without chain lubrication!
If the saw chain runs dry, the cutting equipment may become irrepa-
rably damaged within a short time. Always check chain lubrication
and oil level in the tank before starting work.
NOTE
► Use only saw chain oil, preferably biodegradable. Do not use waste
oil, motor oil, etc.
► While working, check whether the chain lubrication is working
correctly.

Sharpening the saw chain

NOTE
► A bench grinder can be attached to the grinder support
on
secure grip during grinding.
.
► You will find detailed information on sharpening in a sharpening set,
e.g. from Oregon.
► Alternatively, you can use an electrical saw chain sharpening device
and follow the instructions of the manufacturer.
► If you have any doubts about carrying out the work, the saw chain
should be replaced.
to remove the blade
(see section "Tightening and checking the
clockwise using the flat-blade
must lie against the underside of the blade. Check
can be drawn by hand over the blade
stretches and must be tightened more regularly.
.
with approx. 100 ml of organic chain oil
.
clockwise to decrease
anticlockwise to increase
.
.
for a
PBK 4 A2