Herunterladen Diese Seite drucken

Conrad 1070351 Bedienungsanleitung Seite 2

Hdmi cat5 verlängerungssystem

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

HDMI CAT5 extension system
Item no. 1070351
Intended use
The product is intended for transmitting digital video signals over longer distances. The connections
from the playback device to the sender and receiver are facilitated via HDMI cables. The connection
between sender and receiver is facilitated via CAT5/5e/6 network cable. The transmission length
accounts for up to 100 m with a resolution of 1080p.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the
product for purposes other than those described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and
keep them. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
HDMI is a registered trademark of HDMI Licensing L.L.C.
Delivery content
• HDMI CAT5 extension system (1 x sender, 1 x receiver)
• 2 x power adapter
• Mounting material
• 8 x rubber feet
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
• It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• The mains outlet must be located near to the device and be easily accessible.
• As power supply, only use the supplied mains adaptor.
• Only connect the power adaptor to a normal mains socket connected to the public supply.
Before plugging in the power adaptor, check whether the voltage stated on the power adaptor
complies with the voltage of your electricity supplier.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power adaptor from the mains socket by pulling on the cable; always use
the grips on the plug.
• When setting up the product, make sure that the cable is not pinched, kinked or damaged by
sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them. This poses
a risk of injury.
• For safety reasons, disconnect the power adaptor from the mains socket during storms.
• The adapter corresponds to Safety Class II. Only connect to a proper wall socket of the public
electricity supply.
• Never use the product directly after moving it from a cold to a warm room. Condensation might
damage the product under certain circumstances. The power supply can become a danger to
life through electric shock ! Let the product reach room temperature before it is connected and
used. This can take several hours.
• Never cover the product while it is in use.
• Protective measures for electric equipment and relevant utilities according to the employer's
indemnity insurance must be observed when using the product commercially.
• Supervision by trained employees must be guaranteed when using the product in schools,
training facilities or hobby and self-help workshops.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
Operation
• Install the sender near the playback device (e.g. DVD player) and the receiver near the output device
(e.g. TV).
If necessary, attach the rubber feet supplied to the bottom of the product. They are intended to ensure
Version 04/14
stability and to prevent damage to surfaces.
Considering the variety of varnish and polish used on furniture it cannot be ruled out that the
feet of the device leave visible residue on furniture due to chemical reactions. The product
should therefor not be placed on valuable furniture surfaces without using suitable protection
measures.
The housings of the sender and receiver both feature 4 holes each allowing them to be mounted at
appropriate locations. Suitable mounting material (8 screws and expansion pegs each) is included in the
delivery scope.
Caution! Contact an expert if not familiar with the mounting procedure.
• Connect the RJ45 outputs and the RJ45 inputs of the sender and receiver using a CAT 5, CAT 5e (UTP/
STP/FTP) or CAT 6 (UTP) network cable. Observe the maximum transmission length as provided under
Specifications.
• Connect the HDMI input HDMI IN of the sender to the HDMI output of your playback device using an
HDMI cable.
• Connect the HDMI output HDMI OUT of the receiver to the HDMI input of your output device using an
HDMI cable.
• Connect the round plugs of the power adapters to the DC sockets on the sender and receiver and
then connect the power adapters to wall sockets. The power LEDs ON of the sender and receiver both
light up.
• Once the connection between the playback and output devices has been established successfully, the
status LEDs LINK light up green steadily.
• The receiver features 2 additional RJ45 outputs, each of which can connect up to two receivers (not
included). In order to do so, refer to the information on the maximum amount of feasible branches or
displays switchable in series and on transmission lengths as provided under Technical data.
Maintenance and cleaning
Do not use aggressive cleaning agents, spirits or other chemical solutions as they may attack
the casing or even affect the functioning of the device.
• Disconnect the power supply before cleaning. Besides occasional cleaning, the device is maintenance-
free. To clean the device, use a soft, anti-static and lint-free cloth.
• Never submerge the product in water.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste. At
the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil the legal requirements and make your contribution to protecting the environment.
Technical data
a) Power Adapter
Input voltage / current ............................................ 100 - 240 V/AC, 50/60 Hz, 0.5 A
Output voltage / current ......................................... 5V/DC, 2 A
Protection class ..................................................... II
b) HDMI sender and receiver
Nominal voltage/ current ........................................ 5 V/DC, 860 mA (sender)
HDMI connection ................................................... Type A
HDCP support ....................................................... Yes
Resolution, video signal ......................................... max. 1920 x 1080 (1080p), 60 fps
Transmission length............................................... max. 100 m
Switchable transmission lines ................................ max. 31 (at max. 3.1 km)
Displays switchable in series ................................. max. 100
Operating conditions .............................................. 0 to +55 °C, up to 95 % rF (non-condensing)
Storage conditions ................................................. -20 to +85 °C, up to 95 % rF (non-condensing)
Dimensions (W x H x D) ........................................ 140 x 67 x 27 mm (sender)
Weight ................................................................... approx. 200g (sender)
5 V/DC, 950 mA (receiver)
155 x 67 x 27 mm (receiver)
approx. 230g (receiver)
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2014 by Conrad Electronic SE.
V2_0414_02-JH

Werbung

loading