Pioneer KURO PDP-LX6090 Bedienungsanleitung Seite 7

Important user information
Caution
• Pioneer bears no responsibility for any damage arising from
incorrect use of the product by you or other people,
malfunctions when in use, other product related problems, and
use of the product except in cases where the company must be
liable.
Flat screen TV protection function
When still images (such as photos and computer images) stay on
the screen for an extended period of time, the screen will be slightly
dimmed. This is because the protection function of the flat screen
TV automatically adjusts the brightness to protect the screen when
detecting still images; so this does not designate malfunction. The
screen is dimmed when a still image is detected for about three
minutes.
Information of pixel defect
Plasma TVs displays information using pixels. Pioneer flat screen TV
panels contain a very large number of pixels. (Depending on the
panel size; over 3.1 million pixels for a 50 inch/60 inch display). All
Pioneer display panels are manufactured using a very high level of
ultra-precision technology and undergo individual quality control.
In rare cases, some pixels can be permanently switched off, or on,
resulting in either a black or coloured pixel permanently fixed on the
screen.
This effect is common to all plasma TVs because it is a
consequence of the technology.
If the defective pixels are visible at a normal viewing distance of
between 2.5 meters and 3.5 meters whilst viewing a normal
broadcast (i.e. not a test card, still image or single colour display)
please contact the supplying dealer.
If, however, they can only be seen close up or during single colour
displays then this is considered normal for this technology.
Infrared rays
The flat screen TV releases infrared rays because of its
characteristics. Depending on how the flat screen TV is used, the
remote controls of nearby equipment may be adversely affected or
wireless headphones using infrared rays are interfered by noise. If
this is the case, place that equipment at a location where its remote
control sensor is not affected.
Radio interference
While this product meets the required specifications, it emits a
small amount of noise. If you place such equipment as an AM radio,
personal computer, and VCR close to this product, that equipment
may be interfered. If this happens, place that equipment far enough
from this product.
Flat screen TV driving sound
The screen of the flat screen TV is composed of extremely fine pixels
and these pixels emit light according to received video signals. This
principle may make you hear buzz sound or electrical circuit
humming from the flat screen TV.
Do not attach such items as labels and tape to the
product
This may result in the discolouration or scratch of the cabinet.
Downloaded From TV-Manual.com Manuals
When not using the product for a long period of time
If you do not use the product for a long period of time, the functions
of the product may be adversely affected. Switch on and run the
product occasionally.
Condensation
Condensation may take place on the surface or inside of the
product when the product is rapidly moved from a cold place to a
warm place or just after a heater is switched on in winter morning,
for example. When condensation takes place, do not switch on the
product and wait until condensation disappears. Using the product
with condensation may result in malfunction.
Cleaning the surface of the screen
When cleaning the screen surface, gently wipe it with the supplied
dry cleaning cloth.
Caution
Rubbing hard on the screen can scratch the special film coating the
surface. If cleaning gently with the dry cloth is not enough to
remove grime, unplug the power cord from the outlet and follow the
procedure below.
1. Soak a piece of soft, untreated cloth in distilled water.
A "treated" cloth contains polish or other chemicals, such as in a
commercially available eyeglass cleaning towelette.
2. Wring out the cloth so that it is slightly damp, not wet.
Make sure to wring out the cloth completely. Cleaning the surface
with a wet cloth can allow water to seep into the unit, causing
damage.
3. Gently wipe the surface of the screen with the damp cloth.
4. Wipe the surface again using the dry cloth included with your
panel to remove any remaining dampness and to prevent
streaks.
Cleaning the glossy surface of the front cabinet
When cleaning the glossy surface of the front cabinet, gently wipe
it with a dry soft cloth; the supplied cleaning cloth or other similar
cloths (e.g., cotton and flannel). If you use a dusty or hard cloth, the
surface of the product will be scratched.
Cleaning the cabinet
When cleaning the cabinet of this product, gently wipe it with a
clean soft cloth (e.g., cotton and flannel). If you use a dusty or hard
cloth or if you rub the cabinet hard, the surface of the cabinet will
be scratched.
The cabinet of this product is mostly composed of plastic. Do not
use chemicals such as benzene or thinner to clean the cabinet.
Using these chemicals may result in quality deterioration or coating
removal.
Do not expose the product to volatile gas or fluid such as pesticide.
Do not make the product contact with rubber or vinyl products for a
long period of time. The effect of plasticizer in the plastic may result
in quality deterioration or coating removal.
If you clean the surface of the cabinet with a wet cloth, water
droplets on the surface may enter into the product, resulting in
malfunction.
01
7
En