Customizing Channel Related Settings - Pioneer KURO PDP-LX6090 Bedienungsanleitung

Enjoying DTV broadcasts
Checking signal strength
You can check the signal strength and signal quality of each TV
channel.
1 Press HOME MENU.
2 Select "Setup" (/ then ENTER).
3 Select "DTV Setup" (/ then ENTER).
4 Select "Installation" (/ then ENTER).
The password entry screen appears. Enter your four-digit password
using buttons 0 to 9.
5 Select "Signal Check" (/ then ENTER).
6 Select "RF Channel" (/ then ENTER).
7 Select the channel to be checked (/).
Signal Check
RF Channel
Add New Channels
Signal Strength
0 25
Signal Quality
Use "Add New Channels" function here to add channels within the
selected RF channel (receiving frequency).
Note
• You can select "DTV Setup" only when watching DTV channels.
Switching on/off the power to the antenna
Use the following procedure to switch on or off the power to the
antenna connected with the DTV antenna terminal.
1 Repeat steps 1 to 4 provided for Checking signal strength.
2 Select "Aerial Power" (/).
3 Select "On" or "Off" (default) (/).
Caution
• When the "Aerial Power" setting is on, directly connect the
aerial to the ANT input terminal at the rear of the flat screen TV.
Connecting any device between the aerial and flat screen TV
may cause damage to the device.
Note
• You can select "DTV Setup" only when watching DTV channels.
Restoring the system defaults
Use this function only when you wish to reset all the DTV settings to
the factory defaults.
1 Repeat steps 1 to 4 provided for Checking signal strength.
Downloaded From TV-Manual.com Manuals
21
: 77%
50 75
: 100% Good
2 Select "Restore System Defaults" (/ then ENTER).
A confirmation screen appears.
3 With "OK" pressed, the system restores the factory defaults.
Then Auto Installation is initiated automatically.
Note
• The password entry screen does not appear if you have disabled
the password function. For details, see Using a password on
page 56.
• You can select "DTV Setup" only when watching DTV channels.

Customizing channel related settings

This section describes how to customize various channel related
settings. These settings include favourite channel registration,
Channel Skip, and Channel Lock.
Setting Channel Options
Use the following procedure to select individual channels and
switch on the Favourite, Channel Skip, or Channel Lock for the
channels.
100
1 Press HOME MENU.
2 Select "Setup" (/ then ENTER).
3 Select "DTV Setup" (/ then ENTER).
4 Select "Channel Management" (/ then ENTER).
The password entry screen appears. Enter your four-digit password
using buttons 0 to 9.
5 Select "Channel Options" (/ then ENTER).
The Channel Options screen with a list of registered channels
appears.
Channel Options
001 ∗∗∗ ∗∗∗
002 ∗∗∗ ∗∗∗
007 ∗∗∗ ∗∗∗∗∗
030 ∗∗∗∗ ∗∗∗∗∗∗∗
040 ∗∗∗ ∗∗∗∗ ∗∗
051 ∗∗∗ ∗
800 ∗∗∗ ∗∗∗∗∗∗∗∗∗∗
6 Select an individual channel (/// then ENTER to select
on/off).
Select "On" for Favourites if you want the channel to be registered
as your favourite (digital) channels. Selecting from the registered
list may be the easiest way to tune to those channels.
Select "On" for Channel Skip if you want the channel to be skipped
when operating P+/P– on the remote control unit or CHANNEL +/–
on the flat screen TV.
Select "On" for Channel Lock if you want the channel not to be
tuned without password entry.
Channel Skip
09
41
En