Remaining Hazards; Technical Data; Before Starting The Equipment - Parkside PBS 350 A1 Originalbetriebsanleitung

• The bandsaw blade guard should be in its lowest position
close to the bench during transport.
• For miter cuts when the table is tilted, the parallel stop must
be positioned on the lower part of the table.
• Never use guards to lift or transport items.
• Ensure that the bandsaw blade guards are used and cor-
rectly adjusted.
• Keep your hands a safety distance away from the bandsaw
blade. Use a push stick for narrow cuts.
• The push stick has to be stored on the intended device, so
that it can be reached from normal working position and is
always ready to be used.
• In the normal operating position the operator is in front of
the machine.
Warning!
This electric tool generates an electromagnetic field during op-
eration. This field can impair active or passive medical implants
under certain conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with medical
implants consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.

Remaining hazards

The machine has been built using modern technology in ac-
cordance with recognized safety rules. Some remaining haz-
ards, however, may still exist.
• Risk of injury for fingers and hands by the rotating saw band
due to improper handling of the work piece. Risk of injury
through the hurling work piece due to improper handling,
such as working without the push stick.
• Risk of damaging your health due to wood dust and wood
chips. Wear personal protective cloth such as goggles. Use
a fitting dust extractor.
• Risk of injury due to defective saw band. Regularly check
saw band for such defects.
• Risk of injury for fingers and hands while changing saw
band. Wear proper gloves.
• Risk of injury due to starting saw band while switching on
the machine.
• The use of incorrect or damaged mains cables can lead to
injuries caused by electricity.
• Wear only close fitting clothes. Remove rings, bracelets and
other jewellery.
• For the safety of long hair, wear a cap or hair net. Even
when all safety measures are taken, some remaining haz-
ards which are not yet evident may still be present.
• Remaining hazards can be minimized by following the in-
structions in „Safety information", "Intended use" and in the
entire operating manual.
6 GB/CY

7. Technical data

Electric motor
Power
Revolutions n
0
Saw band length
Saw band width
Saw band (pre-assembled)
Cutting speed
Passage height
Passage width
Table size
Slewing range of the table
Max. size of the workpiece
Overall weight
Subject to technical modifications!
* Operating mode S1, continuous operation.
The work piece must have a minimum height of 3 mm and a
minimum width of 10 mm.
The total noise values determined in accordance with EN
61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection!
The effects of noise can cause a loss of hearing.
Keep the noise level and vibration to a minimum!
• Only use faultless devices.
• Maintain and clean the device at regular intervals.
• Adapt your working methods to the device.
• Do not overload the device.
• Have the device checked if necessary.
• Switch the device off if it is not in use.

8. Before starting the equipment

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, store the packaging until the warranty period has
expired.
ATTENTION
The device and packaging materials are not toys! Children
must not be allowed to play with plastic bags, film and small
parts! There is a risk of swallowing and suffocation!
230 - 240 V∼ 50 Hz
S1 350W*
1400 min
-1
1400 mm
3,5-12 mm
6 x 1400 mm
900 m/min
0 - 80 mm
200 mm
300 x 300 mm
0° to 45°
400 x 400 x 80 mm
14,8 kg
77,4 dB(A)
3 dB
90,4 dB(A)
3 dB