Specifications; Mounting Precautions (For Sharp Dealers And Service Engineers) - Sharp PN-65HC1 Installationsanleitung

Model
Power requirement
Operating temperature *
Operating humidity *
2
Power consumption *
3
Dimensions inch (mm)
(excluding protrusions)
Weight
*1 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specified by the optional equipments.
*2 In addition, check the requirements of the computer and other devices to be connected, and make sure that all requirements are satisfied.
*3 When an option is installed in the expansion slot. When not installed, PN-86HC1: 420 W, PN-75HC1: 360 W, PN-65HC1: 200 W.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.

Mounting Precautions (For SHARP dealers and service engineers)

• When installing, removing or moving the monitor, ensure that this is carried out by at least 4 people.
• Be sure to use a wall-mount bracket designed or designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials
such as plaster / thin plastic board / wood before starting installation.
• This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor.
Install by the most suitable method for the material and the structure.
• To attach a VESA-compliant mounting bracket, use M8 screws that are 3/8 inch (10 mm) to 1/2 inch (12 mm) (PN-65HC1:
9/16 inch (15mm)) longer than the thickness of the mounting bracket.
• Do not use an impact driver.
• When moving the monitor, be sure to hold the handles or the parts marked by
This may cause product damage, failure, or injury.
[PN-86HC1]
• If you need to temporarily place the monitor on a table or other surface during installation, spread a thick soft cloth on the
table to prevent damage to the screen and table.
• Prior to repacking or removal, remove the tray.
• After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.
• Do not use any screw holes other than those for mounting brackets, located on the rear of the monitor, for installation.
8
E

Specifications

PN-86HC1
AC 100 - 240 V, 5.9 A, 50/60 Hz AC 100 - 240 V, 5.2 A, 50/60 Hz AC 100 - 240 V, 3.4 A, 50/60 Hz
41°F to 95°F (5°C to 35°C)
1 * 2
20% to 80% (no condensation)
530 W
Approx. 78-1/4 (W) x 4-7/16
(D) x 46-1/4 (H)
(1988 x 113 x 1175)
lbs. (kg) Approx. 176.4 (80)
3/8 - 1/2 inch (10 - 12 mm)
(PN-65HC1: 3/8 - 9/16 inch (10 - 15mm))
[PN-75HC1]
PN-75HC1
460 W
Approx. 68-5/16 (W) x 4-1/8
(D) x 40-13/16 (H)
(1735 x 105 x 1036)
Approx. 134.5 (61)
Screws (M8)
Mounting bracket
Monitor mounting
below. Do not grasp the screen or tray.
[PN-65HC1]
PN-65HC1
300 W
Approx. 59-1/4 (W) x 3-9/16
(D) x 35-9/16 (H)
(1505 x 91 x 902.5)
Approx. 99.2 (45)