Before Commissioning; Attachment And Operation - Parkside PBTS 370 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

Sound pressure level L
pA
Unloaded ................................................................... 80,4 dB(A)
Loaded ....................................................................... 82,2 dB(A)
Uncertainty K ......................................................................3 dB
pA
Sound power level L
WA
Unloaded ................................................................... 88,7 dB(A)
Loaded ....................................................................... 89,4 dB(A)
Uncertainty K .....................................................................3 dB
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing. Total vibration
values (vector sum of three directions) determined according
to EN 62841-1.
The specified total vibration value and the specified noise
emission value have been measured in accordance with a
standardised test procedure and can be used to compare one
power tool with another.
The specified total vibration value and the specified noise emission
value can also be used for an initial estimation of the exposure.
Note:
• The vibration and noise emission values can vary from the
specified values during the actual use of the power tool, de-
pending on the type and the manner in which the power
tool is used, and in particular the type of workpiece being
processed.
• It is necessary to define safety measures to protect the opera-
tor which are based on an estimate of vibration exposure
during the actual operating conditions (for this, all parts of
the operating cycle have to be considered, e.g. times during
which the power tool is switched off and times during which
it is switched on but runs in no-load mode).

8. Before commissioning

8.1 Unpacking
• Open the packaging and carefully remove the device.
• Remove the packaging material, packaging and transport
safety devices (if applicable).
• Check that the delivery is complete.
• Check the device and accessory parts for transport dam-
age.
• If possible, keep the packaging until the end of the war-
ranty period.
DANGER
The device and the packaging are not children's toys! Do not
let children play with plastic bags, films or small parts! There is
a danger of choking or suffocating!
8.2 General notes
• Before connecting the machine, make certain that the data
on the type plate matches with the mains power data.
WARNING
Always pull out the mains plug before carrying out adjustments
on the device.
• Prior to commissioning, all covers and safety devices must be
mounted correctly.
• It must be possible for the sanding belt (13) and sanding
disc (4) to run freely.
• In case of previously machined wood, be aware of any for-
eign bodies, such as nails or screws, etc.
• Before pressing the on/off switch (5), make sure that the
sanding paper is correctly fitted, and that moving parts run
smoothly.

9. Attachment and operation

9.1 Assembling the machine (fig. 1−4)
• Mount the sanding table (7) and secure with the locking
screw (8) (fig. 2, 3). The sanding table (7) can be infinitely
adjusted from 0 ° to 45 ° with the angle scale (9) and the
locking screw (8).
The adjustable transverse stop (6) ensures safe guidance of
the workpiece. Attention! It must be possible for the sand-
ing disc (4) to run freely. The distance between the sand-
ing table (7) and the sanding disc (4) is not allowed to
exceed 1.6 mm.
• Put on the stop rail (14) and secure with the Allen screws
(17) (fig. 4). Attention! It must be possible for the sanding
belt (13) to run freely.
9.2 Changing the sanding belt (fig. 5−8)
• Pull out the mains plug.
• Loosen the Allen screw (12).
• Remove the screws (18).
• Remove the sanding belt guard (19).
• Turn the sanding belt tensioner (3) to the right in order to
reduce the tension on the sanding belt (13).
• Remove the sanding belt (13) to the rear.
• Mount the new sanding belt in reverse order. Attention!
Note the running direction on the housing and on the inside
of the sanding belt!
9.3 Adjusting the sanding belt
• Pull out the mains plug.
• Push the sanding belt (13) by hand slowly in the running
direction.
• The sanding belt (13) must run centrally on the sanding
surface. If not, you can use the knurled screw (1) to make
adjustments.
9.4 Moving the sanding position of the sanding
belt (fig. 9−11)
• Loosen the Allen screw (12).
• Move the sanding belt (13) upwards into the desired po-
sition.
• Tighten the Allen screw (12) again to fix this position.
• In this position you can use the sanding table (7) to support
the workpiece. To do this, first loosen the two Allen screws
(17) and then remove the stop rail (14). The sanding table
(7) can now be pushed into the hole of the holder tube (20)
and fixed with the locking screw (8).
9.5 Replacing the sanding paper on the sanding
disc (fig. 12)
Dismantle the bottom disc guard (15) by removing the 2
screws (16). Pull the sanding paper off the sanding disc (4)
and attach the new sanding paper (quick-fit fastening system).
GB/IE 17