Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Universal car mount for smartphones,
tablets and navigation systems
Item no. 759914
Intended use
The product is intended for mounting a smartphone, a tablet computer or a navigation device
to the windshield inside a car. The suction cups are also suitable for slightly uneven surfaces
such as tiles, floor tiles or sand-blasted glass. The product features two ball joints that allow for
the mounted product to be aligned individually.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Universal car mount
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Operating elements
1
Version 04/15
3
Operation
Choose an installation surface that will not impair your visibility of the road
or cause distraction during driving.
Observe any legal limitations concerning the use of mobile phones,
computers and navigation devices in cars.
Do not exceed the permissible maximum load of 3 kg.
Do not attach any items to the product that are particularly valuable or fragile.
Attention, not suitable for the following products:
Sony Z2 / Z3 (products with glass body).
1. Make sure both suction cups (3), the installation surface and the surface of the device to be
mounted are clean, grease-free, dust-free and dry.
2. Place one of the suction cups on the installation surface and apply some pressure.
3. Push the locking lever (2) toward the installation surface so that the suction cup adheres to
the surface. Make sure that the suction cup is well fastened.
4. Press the rear side of the device to be mounted against the other suction cup.
5. Push the locking lever towards the device in order for the suction cup to fasten. Make sure
that the suction cup is well fastened.
6. Loosen both set screws (1) and align the device as desired. Then refasten both set screws.
7. In order to remove the suction cups from both the installation surface and the mounted
device, lift up the respective locking lever.
Maintenance and cleaning
Never use any aggressive cleaning agents or chemical solutions.
• Clean the suction cups every 4 to 6 months with a slightly damp cloth. In order to do so,
remove the product from the installation surface or take the device, if mounted, from the
suction cup. Use a mild cleaning agent to clean off tougher dirt. Let the suction cups dry
completely before re-attaching them to the installation surface or, respectively, attaching the
device to the product.
• Use a dry, soft and clean cloth to clean the plastic components. You can use a long-haired,
soft and clean brush and a vacuum cleaner to remove dust.
Disposal
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
Technical data
Load............................................................. max. 3 kg
Operating conditions .................................... 0 to +45 ºC, <80 % RH
Storage conditions ....................................... 0 to +45 ºC, <80 % RH
Length.......................................................... max. 90 mm
Suction cup Ø .............................................. 46 mm
Weight ......................................................... 66 g
2
3
1 Set screw
2 Locking lever
3 Suction cup
2
1
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
(www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited. This publication represent the technical status at the time of
printing.
© Copyright 2015 by Conrad Electronic SE.
V2_0415_02-HK
Werbung
