Herunterladen Diese Seite drucken

Conrad 57 18 92 Bedienungsanleitung Seite 2

Led-einbauleuchten für außenbereich

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

O P E R A T I N G I N S T R U C T I O N S
www.conrad.com
Recessed LED-Lights
for outdoor locations
Item-No. 57 18 92  
Intended Use
The LED-lights of the product are intended to be mounted to walls, ceilings and the
ground in outdoor locations where they light e.g. driveways, garages, etc. The includ-
ed special transformer should be used with a voltage of 230V~/50Hz.
Any use other than described above damages the product. Moreover, this involves dan-
gers such as short-circuit, fire, electric shock, etc. No part of the product should be modi-
fied or rebuilt!
The safety instructions must be observed absolutely!
This product complies with the applicable National and European specifications.
Contents
• 3 LED-lights
• 3-way splitter
• Transformer with mains cable
• Operating instructions
Safety instructions
Please read the operating instructions through completely before
putting the device into operation. They contain important informa-
tion for correct operation.
In the case of any damages which are caused due to the failure to
observe these operating instructions, the guarantee will expire! We
do not accept liability for consequential damage!
We do not accept liability for damage to property or personal injury
caused by improper handling or non-compliance with the safety
instructions! In such cases the guarantee will lapse.
• The unauthorized conversion and/or modification of the product is inad-
missible for safety and approval reasons (CE).
• Do not expose the product to extreme temperatures, strong vibrations
or strong mechanical stress.
• Keep the product out of reach of children! There is the risk of a danger-
ous electrical shock.
• The product complies with protection class II; the mains plug of the spe-
cial transformer is a so-called contour plug.
• The special transformer should only be used with a power voltage of
230V~/50Hz. Never try to use the transformer with any other voltage, it
will be destroyed.
• Do not use the product inside of rooms or in bad ambient conditions
where flammable gases, vapours or explosive dust may be present or
are present!
• The product should not be mounted in flood-prone areas or in areas such as
e.g. depressions where rain water could accumulate.
• The transformer ist splash-proof according to IP64.
Whereas the first digit „6" indicates that there is a complete protection
against touching of energised or moved inner parts and against intru-
sion of dust.
The second digit „4" indicates protection against splash water (which
can hit the transformer from all directions without any deleterious
effect).
• The 3 LED-lights are protected according to IP65.
Wheras the first digit „6" indicates that there is a complete protection
against touching of energised or moved inner parts and against intru-
sion of dust.
The second digit „5" indicates the protection against sprayed water; a
water jet targeted at the device from all directions must not have any
deleterious effect.
• In order to avoid any injury of the eyes, never look directly into the light
and never direct the light beam at people or animals.
• A damaged mains cable cannot be replaced. If the mains cable is dam-
aged do not use the product any longer but dispose it in an environ-
mentally friendly way.
• Do not carelessly leave the packaging material lying around since this
may become a dangerous toy for children.
• In commercial and industrial facilities, the regulations for the prevention
of accidents as laid down by the professional trade association for elec-
trical equipment and devices need to be observed.
Mounting preparations
Please note:
• The special transformer can be mounted and used in a protected outdoor location
Version 07/07
due to its type of construction and protection (IP64). Which means that it should not
°
be exposed to direct rainfall. Mount it e.g. unter roof eaves or inside of a garage or
similar.
• In contrast, the LED-lights may be mounted and used in outdoor locations (IP65).
They, however, should not be mounted or used in or under water!
• A suitable mains socket for connecting the product in an outdoor area must be avail-
able.
• The product must be mounted and operated out of reach of children.
• Ensure that no one can stumble on the device or the cable in the mounting area.
Lay all the cables in a way that they won't be damaged by later garden work (e.g.
digging up a flowerbed) or by sharp edges (e.g. of stones). Furthermore you must
ensure that the cables cannot be stepped on or passed over by vehicles.
• The product has to be protected in the on-site sub-distribution by a 10/16A-fuse.
Mounting
Please note the information of the chapter „Mounting prepara-
tions"!
• Because of the small design of the LED-lights there is a variety of mounting loca-
tions, e.g. on a wall, in a garage, as path illumination, as design light for terraces or
similar.
The LED-lights, however, must not be operated in or under water! The same applies
to the 3-way splitter.
• A hole with a diameter of about 35mm and a depth of about 55mm is needed each
for mounting the LED-lights.
The LED-light is fixed in the hole by three attached steel springs. Compress the
steel springs a lilttle and and insert the LED-light carefully into the designated
opening.
• Connect the wires of the three LED-lights to the 3-way splitter. Plug each into its
designated socket and fasten the cap nut in order to prevent water from entering.
Do not use any tools because the plastic cap nut would be damaged!
• Plug the connector of the splitter into the corresponding socket of the special trans-
former and fasten the cap nut.
• Mount the special transformer in an appropriate protected location.
Never expose the special transformer to direct rainfall and never operate
it in or under water! Danger of life by an electric shock!
Attention!
Take care not to damage existing lines for power supply, gas or water
when tightening the product or drilling the mounting holes.
Furthermore you have to make sure the special transformer is not mounted
within isolation material or similar because there is the danger of overheating
and fire!
Ensure that there is enough space, at least 20cm, around the outside of
the special transformer 20cm.
• Connect the plug (contour plug) of the special transformer to an applicable socket.
After turning on the voltage (or after connecting the power plug) the LEDs should
light up.
Care and maintenance
The product is maintenance-free. Never dismantle the product.
Before cleaning disconnect the mains plug from the power supply.
The outside of the housing should only be cleaned with a clean, soft, dry cloth. For
cleaning stronger impurities of LED-lights the cloth may be moistend with lukewarm
water.
Never use aggressive cleaning agents or chemical solutions as the surface of the hous-
ing could be damaged (discolouration) or the function may be affected.
Do not press too much on the glass or the housing to avoid scratch marks.
Handling
• If a safe operation is no longer assumed put out the device of operation and secure
it against accidential use.
Safe operation must be presumed to be no longer possible, if:
the device is visibly damaged
the device no longer functions
the device was stored under unfavourable conditions for a long period of time or
it was exposed to extraordinary stress caused by transport
• Never touch the mains plug with damp or wet hands.
Danger of life by an electric shock!
• The LED-light must not be driven on by vehicles. The same is applicable to the con-
nection cables and all other product components.
You should not step on the LED-lights because it would leave scratch marks and the
glass could break.
Lay the cables in a way no one can step on them.
Disposal
Please dispose of the device, when it is no longer of use, according to the
current statutory requirements.
Technical data
Voltage/Transformer:. . . . . . . . . . . . . . 230 V~/50Hz
Output:. . . . . . . . . . . . . . . . . . . . . . . . . 12V~, 0.5A
Protection category:. . . . . . . . . . . . . . . IP64
Protection class: . . . . . . . . . . . . . . . . . II
Working temperature: . . . . . . . . . . . . . -20°C to +40°C
LED-lights: . . . . . . . . . . . . . . . . . . . . . . 3 units, 6 LEDs each
Protection category:. . . . . . . . . . . . . . . IP65
Necessary mounting hole: . . . . . . . . . . Ø 35mm, depth 55mm
Working temperature: . . . . . . . . . . . . . -20°C to +40°C
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
The operating instructions reflect the current technical specifications at time of
print. We reserve the right to change the technical or physical specifications.
© Copyright 2007 by Conrad Electronic SE. Printed in Germany.

Werbung

loading