Kenwood KM280 Serie Bedienungsanleitungen Seite 6

speed switch
These are a guide only and will vary depending upon the quantity of mix in
the bowl and the ingredients being mixed.
beater
creaming fat and sugar start on min gradually increasing to a higher
●
speed
beating eggs into creamed mixtures use a medium to high speed
●
folding in flour, fruit etc use a low to medium speed
●
all in one cakes start on a low speed gradually increasing
●
to a higher speed
rubbing fat into flour use a low to medium speed
●
whisk
Gradually increase to maximum
●
dough hook
Use a low to medium speed
●
maximum capacities
shortcrust pastry
sponge cake (one stage mix) 1.6 Kg total mix
fruit cake mix
bread dough
egg whites
electronic speed sensor control
Your mixer is fitted with an electronic speed sensor control that is designed
to maintain the speed under different load conditions, such as when
kneading bread dough or when eggs are added to a cake mix. You may
therefore hear some variation in speed during the operation as the mixer
adjusts to the load and speed selected - this is normal.
to fit and use the splashguard
1 Fit the bowl into the base and add the ingredients.
2 Fit the tool then lower the mixer head
3 Fit the splashguard onto the bowl by sliding the cut away section around the
mixer head .
4 To remove the splashguard reverse the above procedure.
During mixing, ingredients can be added directly to the bowl via the chute.
●
care and cleaning
Always switch off and unplug before cleaning.
●
power unit
Wipe with a damp cloth, then dry.
●
Never use abrasives or immerse in water.
●
bowl, tools, splashguard, removable guard on dough hook
Wash by hand, then dry thoroughly or wash in the dishwasher.
●
Never use a wire brush, steel wool or bleach to clean your stainless steel
●
bowl. Use vinegar to remove limescale.
Keep away from heat (cooker tops, ovens, microwaves).
●
450g flour weight
1.8 Kg total mix
500g flour weight
8
Blenders AT282 and AT283
Use the blender for soups, drinks, pâtés, mayonnaise, breadcrumbs, biscuit
crumbs, chopping nuts and crushing ice.
safety
Liquids should be allowed to cool to room temperature before blending.
●
Don't touch the sharp blades. Keep the blade unit away from children.
●
Only use the goblet with the blade unit supplied.
●
Never attempt to fit the blade unit to the machine without the goblet fitted.
●
Always unplug the machine before putting your hands or utensils in the
●
goblet.
Never run the blender empty.
●
Only operate the blender with the lid in place.
●
Never fit the blade unit to the power unit without the blender
●
goblet fitted.
Always take care when handling the blade assembly and avoid touching the
●
cutting edge of the blades when cleaning.
When removing the blender from the power unit:
●
switch off;
● ●
wait until the blades have completely stopped;
● ●
model AT283 care should be taken not to unscrew the goblet from the
● ●
base assembly
Misuse of your blender can result in injury.
●
important
The skirt on the bottom of the AT282 acrylic goblet is fitted
during manufacture and no attempt should be made to remove
it.
The attachment will not operate if it is incorrectly assembled
●
or incorrectly fitted to the kitchen machine or if the medium
speed outlet cover is not fitted.
Never run the blender for longer than one minute - it will overheat. Switch off
●
as soon as you have the right consistency.
Don't put dry ingredients into the blender before switching on. Cut them into
●
cubes, then remove the filler cap and drop the cubes through the hole in the
lid whilst the machine is running.
model AT282 don't process spices such as cloves, dill and cumin seeds -
●
they damage the acrylic.
Don't use the blender as a storage container. Keep it empty before and after
●
use.
Never crush ice on its own, always add a little water.
●
model AT282 never blend more than 1.5 litres (2 pints 12fl oz) - less for
●
frothy liquids like milk shakes.
model AT283 never blend more than 1.2 litres (2 pints 2fl oz) - less for
●
frothy liquids like milk shakes.
Smoothie recipes - never blend frozen ingredients that have formed a solid
●
mass during freezing, break it up before adding to the blender.
key
acrylic blender AT282
lid
filler cap
goblet
sealing ring
blade unit
glass blender AT283
filler cap
lid
goblet
sealing ring
blade unit
base
to use your acrylic blender
1 Ensure the sealing ring is correctly fitted on the blade unit.
2 Hold the underside of the blade unit and insert the blades into the base of
the blender. Twist to lock the assembly firmly in place.
3 Put your ingredients into the goblet.
4 Fit the lid to the goblet and twist clockwise into place, making sure that the
tab on the lid slots into the groove in the handle. When correctly fitted the
markings should align .
4
(if supplied)
AT282