Bestway ACTIVERIDGE X4 Bedienungsanleitung Seite 3

INTRODUCTION
Proper Use
Any use other than that described or any modification of the
product is not permissible and may result in injury and/or damage
to the product. The manufacturer is not liable for damage caused
by improper use. The product is not intended for commercial use.
Description of parts and features
A
outer tent long pole
1PC 2PCS
C
guy rope peg
6PCS 15PCS
F
carry bag manual
1PC 1PC
Tent Dimensions ：
Inner tent: 235cm x 205cm x 135cm
Outer tent: (100cm + 210cm) x 240cm x 135cm
Pitching dimension: 320cm x 250cm
W1
W2
L1
L2 L3
WARNING
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
Keep all flames and heat sources away from this tent fabric. We
recommend that you always position your tent upwind from a camp
fire. This will reduce the chances of having embers land on your
tent. In case of fire, please find the exit to escape from the fire.
Never set up the tent near the river, under the tree of other
objective hazards.
Keep exits clear.
Make sure ventilation openings are open all the time to avoid
suffocation.
SAVE THESE INSTRUCTIONS
ASSEMBLY
Setting up the tent
B1
E
FIG1
303021222300_68091_14x21cm_四人野营双层帐篷说明书_英
Owner's Manual
Model No.#68091
ACTIVERIDGE 4 Tent
B1 B2
short pole
1PC
D E
inner tent
1. Lay the inner tent<E> on the ground. Pull the four corners
1PC
2. Push the poles<B1> completely into the channels.(FIG1)
G
3. Stand the inner tent<E> up and push the ends of the
4. Fasten the roof of the inner tent<E> onto the pole junction with
5. Push the pole<B2> completely into the channel on the awning
6. Now carefully place the outer tent<A> over the inner
7. Push the ends of the pole<B2> into the ground sleeves(which
8. Secure the outer tent<A> by pushing the tent pegs<D> into the
H
9. Tie one end of the guy ropes<C>onto the four corner hoops of
10. Tie the other end onto the tent pegs<D> and fasten them by
11. Note: Ensure that guy ropes<C> are about at an angle of 45°
12. Do not pull the guy ropes<C> too tight.
DISASSEMBLE AND MAINTENANCE
Follow steps 1-12 in reverse order.
1. Clean the tent and remove any stains with sponge and cool
2. Never machine wash or machine dry the tent. Hand wash and
3. Please allow all parts to dry thoroughly before you repack the
4. Stitch with thread to repair minor leaks, fabrics and plastic
B1
5. Silicone spray could be use onto zippers if stick
STORAGE
Store the tent in the stuff sack and place it in a cool, dry area out
of sunlight and away from heat sources and rodents.
E
FIG2
3
A
B2
FIG3
C
45°
FIG5
outwards.
Note: Make sure that the channels for the poles<B1> are
facing upwards.
Note: Make sure that the zip on the entrance to the tent is
closed.
poles<B1> into the ground sleeves (which are on the each
corner of the inner tent<E>).(FIG2)
the sewn-on tie.(FIG2)
of outer tent<A>.(FIG3)
tent<E>.(FIG4)
are on the awning of the inner tent<A>.)(FIG4)
ground loops.(FIG5)
outer tent<A>.(FIG5)
inserting the tent pegs<D> into ground.(FIG5)
water. Please use non-detergent soap for serious cleaning.
air dry.
tent. This will prevent the formation from mould, bad odours
and discolouration
sheets damage. Use ropes to connect broken frame parts. Use
tapes to repair the coating broken parts.
A
B1
D
E
FIG4