Before Starting The Equipment - EINHELL TE-CB 18/180 Li Solo Originalbetriebsanleitung

Sound pressure level L ............................ 78 dB
pA
Uncertainty K ............................................. 3 dB
pA
Sound power level L ................................ 91 dB
WA
Uncertainty K ............................................ 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Vibration emission value a
h
Uncertainty K = 2.3 m/s²
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
Anl_TE_CB_18_180_Li_Solo_SPK9.indb 17 Anl_TE_CB_18_180_Li_Solo_SPK9.indb 17
GB
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Fitting the blower tube (Fig. 2)
Connect the motor unit (3) and blower tube (1)
together (Fig. 2).
= 4.6 m/s²
To secure the blower tube, turn it clockwise until it
clicks into position (Fig. 2).
5.2 Fitting the attachable nozzles (Fig. 3)
Fit the attachable nozzles (5) in the same way as
the blower tube (1).
To do so, remove the blower tube (1) from the mo-
tor unit (3) and then fi t the attachable nozzles (5).
You will have to use a diff erent nozzle (5a or 5b)
according to the type of valve.
5.3 Charging the Li battery pack (Fig. 4-5)
1. Remove the battery pack (D) from the handle,
pressing the pushlock button (A) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(E) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack (D) onto the battery
charger (E).
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts whether the charging unit is in place.
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
- 17 -
Autogoods "130"
12.12.2017 16:53:44 12.12.2017 16:53:44