Configuring Input Channels And Output Channels; Linking Two Channels; Selecting A Signal Source; Mixer - Monacor DSM-26LAN Bedienungsanleitung

5.3 Configuring input channels and output channels

Figure 3 on page 2 shows the signal processing chain of the units
DSM-26LAN, DSM-48LAN and DSM-48DT . The settings of the signal
processing blocks shown can be made via the display (5) by means
of the buttons (4) and the rotary knob SELECT/ENTER (7) . To change
the setting of an input channel or output channel:
1) Use the buttons CH/ to select the channel to be set .
2) Use the button ITEM / to select the function to be set .
3) Use the rotary knob SELECT/ENTER (7) to set the value or option
desired .
4) For signal processing functions with multiple parameters, press the
knob SELECT/ENTER after you have set a value . The next parameter
will be shown .
Please refer to figure 6 for the entire menu structure of the input
channels and to figure 7 for the entire menu structure of the output
channels .

5.3.1 Linking two channels

All input channels and output channels can be linked to pairs (e . g .
for stereo signals): A channel with an uneven number will be linked
to the next higher channel . The higher channel will adopt the settings
of the lower channel . Exceptions: Settings of
muting via the button MUTE (9) .
To link two channels:
1) Select one of the channels to be linked .
2) Call up the function
3) Select the option
On
The channels can now only be selected together (e . g .
) . Settings made while the channels are linked will always
Out 34
apply to both channels .
Exceptions: Settings of
and muting via the button MUTE (9) .
Phase
To disable a link:
1) Select the channels linked .
2) Call up the function
3) Select the option
Off

5.3.2 Selecting a signal source

The input channels C and D of the DSM-48... can alternatively process
analog or digital input signals .
In D Link Off ,
I /
C / Limiter Thr.: 22.25dBu
I /
In C Compr. Thr.: 10.50dBu
I /
C / PEQ 1 ... 10 Freq:
I /
In B
HighPass Freq:
I /
C /
LowPass Freq:
I /
In A Delay 1.200ms
I /
C / Source Analog
I /
Out 8 Gain -16.50dB
Fig. 6 Menu structure for the settings of the input channels
26

Mixer

.
Link
.
(not available for linked channels) and
Mixer
.
Link
.
On S
S E Rel.: 50
S E Att.: 50ms
20Hz S E Gain: -2.75dB
200Hz S E Type: LR 24dB
4000Hz S E Type: LR 24dB
S E 1.35Feet S E
S AES Stereo S Dante
S
The source can only be selected together for both channels; there-
fore, first link the appropriate two channels (
selecting a different signal source . When you have selected the signal
source, unlink the channels again in order to be able to make settings
to the individual channels .
1) Select the linked input channels
2) Call up the function
3) Select the signal source
(DSM-48DT only) .
5.3.3 Mixer
For each output channel, it is possible to set the input signal it shall
receive and, in case of multiple signals, the mixing ratio to be used .
Note: Mixer settings must always be made for individual channels . Therefore,
unlink the appropriate channels for this setting .
1) Select the output channel to be set .
2) Call up the function
3) Set the signal attenuation for all input channels . When the atten-
uation is set to its maximum value,
and the input signal will not be routed to the respective output .

5.3.4 Setting the gain

and and
Phase
Use the gain to set the volume of an input channel or output channel .
1) Select the channel to be set .
2) Call up the function
3) Set the gain value . When the gain is set to its minimum value,
Mute

5.3.5 High pass filter and low pass filter

or
In AB
Each input channel and output channel is provided with a high pass
filter and a low pass filter: When these filters are combined, they
may, for example, assume the function of a crossover network (for
frequency-dependent splitting of an input signal to two or more out-
put channels) . Various filter types with different slopes are available .
1) Select the channel to be set .
2) Call up the function
3) Set the cut-off frequency desired . When the frequency of a high
pass filter is set to its minimum value or the frequency of a low
pass filter to its maximum value,
and the filter will have no effect .
4) Select the filter characteristic, i . e . the filter type and the slope of
the filter:
S E
S E Hold: 50ms S E Rel.: 155ms
S E Q: 1.00 S E Type:
S E Enabled: Off , On
S E Enabled: Off , On
411mm S E
IN 34
.
Source
Analog
.
Mixer
.
Gain
will appear on the display and the channel will be muted .
or
HighPass
Off
S E Ratio: 5.00:1
Off ,
Bell S E Enabled: On
S E
S E
C / = CH / CH I / = ITEM / ITEM
☞
chapter 5 .3 .1) prior to
.
, or
AES Stereo Dante
will appear on the display
Off
.
LowPass
will appear on the display
S E Gain: 3.25dB S
S E
S = SELECT E = ENTER
E