Pioneer SC-LX 75 Kurzanleitung Seite 8

Before you start
01
9 i/j/k/l/ENTER
Use the arrow buttons when setting up your
surround sound system and the Audio or Video
options.
10 Receiver Control buttons
Set the remote control operation selector
switch to RECEIVER first to access:
! STATUS – Press to check selected receiver
settings.
! PHASE CTRL – Press to switch on/off Phase
Control or Full Band Phase Control.
! CH LEVEL – Press repeatedly to select a
channel, then use k/l to adjust the level.
! THX – Press to select a Home THX listening
mode (page 29).
! PQLS – Press to select the PQLS setting.
! AUTO/ALC/DIRECT – Switches between
Auto Surround, Auto Level Control, Optimum
Surround mode and Stream Direct mode.
! STEREO – Press to select stereo playback
mode.
! STANDARD – Press for Standard decoding
and to switch various modes (2 Pro Logic,
Neo:X, etc.) (page 28).
! ADV SURR – Use to switch between the
various surround modes (page 28).
! SIGNAL SEL – Use to select an input signal.
! SLEEP – Use to put the receiver in sleep mode
and select the amount of time before sleep.
! DIMMER – Dims or brightens the display.
! A.ATT – Attenuates (lowers) the level of an
analog input signal to prevent distortion.
! SBch – With this receiver, SBch cannot be
used.
! MCACC – Press to switch between MCACC
presets.
! HDMI OUT – Switch the HDMI output
terminal.
11 LIGHT
Press to turn on/off the illumination for the
buttons.
! Press and hold in the LIGHT button for 5
seconds to change the illumination mode 1
8
En
or 2. When set to LIGHT MODE 2 (default),
the illumination only lights when the remote
control LIGHT button is pressed. When
switched to LIGHT MODE 1, the illumination
lights whenever buttons are operated.
Setting LIGHT MODE 1 will shorten the
service life of the batteries.
12 Remote control operation selector
switch
Set to RECEIVER to operate the receiver, TV or
SOURCE to operate the TV or the source device.
When this switch is set to RECEIVER, the
receiver can be controlled (used to select the
white commands). Also use this switch to set
up surround sound.
13 VOL +/–
Use to set the listening volume.
14 MUTE
Mutes the sound or restores the sound if it has
been muted (adjusting the volume also restores
the sound).
Remote control display
The display lights when a remote control opera-
tion is performed, then turns off after 20 sec-
onds if no other operation is performed. When
in the Remote Setup mode, the setup is can-
celed and the display turns off if no operation is
performed for 1 minute.
Remote control display for infrared
signal transmission (default)
1 2 3 4 5 6
MAIN IR SOURCE
iPod/USB
7
Remote control display for RF two-
way communications
1 2 3 4 5 6
MAIN RF RCV CTRL
AV RECEIVER
+12.
VIDEO 0dB
1. Adv MCACC
8 9 10 11 12
! This is displayed when an RF adapter is
connected to the receiver and paired with the
remote control.
! Depending on the communications
environment, two-way communications may
not work well and the remote control display
may not reflect the receiver's status.
1 Remote control operating zone
indicator
This indicates which zone the remote control is
currently set to operate. The display indicates
the setting of the MULTI-ZONE operation selec-
tor switch.
Only when RF two-way communications:
The box display here indicates the communica-
tion status between this remote control unit and
the receiver.
MAIN (White box with black letters): Two-
way communications are established and the
receiver's power is on.
(Gray box with black letters): Two-way
MAIN
communications are established and the
receiver's power is off.
MAIN (White letters only): Two-way commu-
nications are not working well. In this case, the
area indicating the receiver's status (12) is not
displayed.
2 Remote control code sending indicator
This appears when signals are sent from the
remote control.
3 Remote control code sending mode
indicator
This indicates whether remote control codes
are being sent by infrared (IR) signal or RF
communications.
4 Remote control operation indicator
This indicates which operation mode the
remote control is currently set to. The display
indicates the setting of the remote control
operation selector switch.
5 Input function and sending code
indicator
This indicates what input function can currently
be operated with the remote control. Also, when
a button is pressed and its operation code is
sent, the name of that code is displayed.
6 Area indicating the remote control's
status
7 Nothing displayed
Nothing is displayed here when the remote
control code sending mode is set to IR.
8 Scroll indicators
Light when there are more selectable items
when making the various settings.
9 Receiver input indicator
This indicates the input function currently
selected for the receiver's zone.
10 Receiver display
The same information as on the receiver's dis-
play is displayed here.
11 Master volume display
This indicates the volume of the receiver's
main zone using, as an icon and in decibels
(dB). When the sound is muted, the icon is
displayed.
12 Area indicating the receiver's status