Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Connecting your equipment
02
Connecting other audio components
This receiver has both digital and analog inputs, allowing you to connect audio components for
playback.
When you set up the receiver you'll need to tell the receiver which input you connected the compo-
nent to (see also The Input Setup menu on Operating Instructions in CD-ROM).
Turntable
IN
4
IN
5
IN
1
IN
2
(VIDEO)
(DVD)
HDMI
BD IN
ASSIGNABLE
1 6
COMPONENT VIDEO
ASSIGNABLE
Y
P
P
B
R
IN
1
(DVD)
IN
2
(DVR/
BDR)
ZONE 2
ZONE 3
DVD
TV/SAT VIDEO
DVR/BDR
OUT
OUT
IN
IN
IN
OUT
IN
3
(VIDEO)
MONITOR
OUT
ZONE2
OUT
A
FRONT
R
RS-232C
AM LOOP
FM UNBAL 75
SPEAKERS
ANTENNA
IR
IN 1
IN
1
OUT
CU-RF100
IN 2
OUT
2
(OUTPUT 12 V
(OUTPUT 5 V
TOTAL 150 mA MAX)
150 mA MAX)
CONTROL
12 V TRIGGER
! If your turntable has line-level outputs (i.e., it has a built-in phono pre-amp), connect it to the CD
inputs instead.
! You can't hear HDMI audio through this receiver's digital out jack.
22
En
MD, DAT, etc.
Select one
AUDIO OUT
DIGITAL OUT
R
ANALOG
L
COAXIAL
OPTICAL
IN
6
ADAPTER PORT
OUT 1
DC OUTPUT
(DVR/BDR)
(OUTPUT 5 V
(CONTROL)
OUT 2
for WIRELESS LAN
LAN
AC IN
(OUTPUT
0.1 A MAX)
(10/100)
5 V
0.6 A MAX)
VIDEO
COAXIAL
OPTICAL
ASSIGNABLE
ASSIGNABLE
SIGNAL
IN
1
IN
2
IN
1
IN
2
IN
3
OUT
MONITOR
OUT
GND
(
DVD
)
(
CD
)
(
TV/SAT
)
(
DVR/BDR
)
(
VIDEO
)
PHONO
IN
IN
CD IN
FRONT
SUBWOOFER
SURROUND SURR BACK F HEIGHT
F WIDE
FRONT
CENTER
SURROUND SURR BACK
1
2
(Single)
L
R
AUDIO
CENTER
PRE OUT
MULTI CH IN
SUBWOOFER
B
CENTER
FRONT HEIGHT
FRONT WIDE /
SURROUND
L
R
L
R
L
R
L
R
Connecting AM/FM antennas
Connect the AM loop antenna and the FM wire
antenna as shown below. To improve reception
and sound quality, connect external antennas
(see Connecting external antennas on page 22).
DIGITAL IN
OPTICAL
5
AM LOOP
ANTENNA
a
b
1 Pull off the protective shields of both
AM antenna wires.
A
SURROUND BACK
L
2 Push open the tabs, then insert one
(Single)
wire fully into each terminal, then release
the tabs to secure the AM antenna wires.
3 Fix the AM loop antenna to the
attached stand.
To fix the stand to the antenna, bend in the
direction indicated by the arrow (fig. a) then clip
the loop onto the stand (fig. b).
! If you plan to mount the AM antenna to a
wall or other surface, secure the stand with
screws (fig. c) before clipping the loop to the
stand. Make sure the reception is clear.
4 Place the AM antenna on a flat
surface and in a direction giving the best
reception.
5 Connect the FM wire antenna into the
FM antenna socket.
For best results, extend the FM antenna fully
and fix to a wall or door frame. Don't drape
loosely or leave coiled up.
Connecting external antennas
To improve FM reception, connect an external
1
2
FM antenna to FM UNBAL 75 W.
3
4
FM UNBAL 75
AM LOOP
c
ANTENNA
To improve AM reception, connect a 5 m to 6
m length of vinyl-coated wire to the AM LOOP
terminals without disconnecting the supplied
AM loop antenna.
For the best possible reception, suspend hori-
zontally outdoors.
Outdoor antenna
AM LOOP
FM UNBAL 75
ANTENNA
75
coaxial cable
FM UNBAL 75
Indoor antenna
(vinyl-coated wire)
5 m to 6 m
Werbung
Kapitel
Inhaltsverzeichnis
