Herunterladen Inhalt Inhalt Diese Seite drucken

Preparing For Use; Attaching The Disc Guard Cover Using The Quick-Release Fastener - Parkside PWS 230 SE Bedienungs- Und Sicherheitshinweise

Winkelschleifer
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

General safety advice for electrical power tools / Preparing for use
A tip! Using the device safely.
disc. If you work in the other direction there is
the risk of kickback. The device may be forced
out of the cut.
J
Always switch on the device before
placing it against the workpiece. After
cutting or grinding, always lift the device from
the workpiece before switching it off.
J
When working always hold the device
securely with both hands (see Fig. D).
Always keep proper footing and balance.
J
For the best grinding performance move the
device evenly to and fro over the workpiece
maintaining an angle of 15° to 30° (between
grinding disc and workpiece).
J
When working on inclined surfaces do
not press the device hard down on to
the workpiece. If the speed slows greatly,
use less pressure. This will allow you to work
more effectively and safely. If the device sudden-
ly stops due to it becoming retarded or trapped,
pull the mains plug from the socket immediately.
J
Cutting: Advance the device at an
appropriate rate. Do not incline the
cutting disc.
J
roughing, grinding and cutting discs
get hot during use – allow them to
cool fully before touching them.
J
Never use the device for a purpose
for which it was not intended.
J
Before you insert the mains plug into
the socket, always check that the de-
vice is switched off.
J
If a dangerous situation arises, pull
the mains plug immediately out of the
mains socket. Ensure that the device and
the mains plug are easily accessible and can
be reached quickly in an emergency.
J
When taking a break from your
work, before carrying out any tasks
on the device itself and when you are
not using the device, always pull the
14 GB/IE/CY
Downloaded from
www.Manualslib.com
DANGEr! Always guide
the device through the
workpiece against the di-
rection of rotation of the
manuals search engine
mains plug out of the mains socket.
Always keep the device clean, dry and free of
oil or grease.
J
remain alert at all times! Always watch
what you are doing and proceed with
caution. Do not use the device if you cannot
concentrate or you are feeling unwell.

Preparing for use

Q
Take note of the mains voltage. The mains voltage
at the mains socket must match that shown on the
rating plate on the device. Devices marked with
230 V can also be operated at 220 V.
Attaching the disc guard cover
Q
using the quick-release fastener
J
WArNING!
DANGEr OF INjUry!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
DANGEr OF INjUry! Always use the
angle grinder with the disc guard
cover in place. The disc guard cover must
be securely attached to the angle grinder. To
ensure the highest level of safety while using
the device, ensure that the smallest possible
area of the grinding or cutting tool is exposed
to the operator at all times. The disc guard cov-
er is there to protect the operator from pieces
breaking off and accidental contact with the
grinding or cutting tool.
DANGEr OF INjUry! Ensure that the
guard
is attached so that its edge
7
is beyond the angle of the auxiliary
handle
(see Fig. B). Otherwise you
6
could injure yourself against the grinding or
cutting disc.
j
Open the clamping lever
j
Insert the disc cover guide
projection
in the coded groove
9
j
Turn the disc guard cover
position (working position). The closed side of
the disc guard cover
the operator.
.
8
with the coded
7
.
16
into the desired
7
must always be facing
7

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis