Bestway Hydro-Force Benutzerhandbuch Seite 3

OWNER'S MANUAL
WARNING
IMPORTANT SAFETY INSTRUCTIONS
Follow all the Safety and Operating Instructions. If you don't
follow these instructions, it may cause the boat to overturn or
explode and result in drowning.
1. Do not exceed the maximum recommended number of persons.
Regardless of the number of persons on board, the total weight
of persons and equipment must never exceed the maximum
recommended load. Always use the seats / seating spaces
provided.
2. When loading the craft, never exceed the maximum recommended
load: Always load the craft carefully and distribute loads appropriately
to maintain design trim (approximately level). Avoid placing heavy weights high up.
NOTE: The maximum recommended load includes the weight of all persons onboard, all provisions and
personal effects, any equipment not included in the light craft mass, cargo (if any) and all consumable
liquids (water, fuel, etc.).
3. When using the boat, life saving devices such as life jackets and buoys should be pre-inspected and
used at all times.
4. Before every use, carefully inspect all boat components including air-chambers, grab ropes, oars, and
air valves, to ensure everything is in good condition and tightly secured. If you find any damage, please
stop to repair it.
5. Buckets, water scoops and air pumps should always be available in case of air leakage or if the boat
takes on water.
6. When the boat is in motion, all passengers must remain seated at all times to avoid going overboard.
Keep the boat balanced. Uneven distribution of persons or load in the boat may cause the boat to
overturn and result in drowning.
7. Use the boat near the shore and beware of natural factors such as wind, tide waters and tidal waves.
BE AWARE OF OFFSHORE WINDS AND CURRENTS.
8. If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate the other
air chamber to prevent the boat from sinking.
9. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement, shells, glass,
etc. may puncture the boat. To avoid damage, do not drag the boat on rough surfaces.
10. When choosing an outboard motor, refer to the technical specifications section of this manual to
determine acceptable horsepower ratings.
11. For electrical motors equipped with batteries, note that battery acid can be caustic, which can cause
damage to both skin and boat materials.
12. For motors which use fuels such as gas, oil or petrol, since fuel is a flammable substance, it should be
kept away from open flames. Further, clean the boat material immediately if fuel spatters onto the boat
surface. Be aware of the potential harmful efects of liquids such as battery acid, oil or petrol. The liquids
may damage your boat.
13. Inflate according the numbered air chamber and rated pressure of the boat, or it will cause over-inflation
and potential and boat explosion. Exceeding the data given on the capacity plate may cause the craft to
be damaged, overturn and lead to drowning.
14. If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage may occur.
15. Know how to operate a boat. Check in your local area for information and/or training as needed. Inform
yourself about local regulations and dangers related to boating and/or other water activities.
SAVE THESE INSTRUCTIONS
#65046
008
002
003
005 007
006
#65047
009
008
001
010
003
007
006
#65049
008
010
003
007
006
303021213995_21x28.5cm(65046/65047/65049/65062)_20季说明书
TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals, Videos Or
Spare Parts, Please Visit
bestwaycorp.com/support
Part No. Description QTY SPARE PART NO.
001 Boat 1 P04760
001
002 Bench seat
1 F3H101ASS17
003 Floor board 1
P03777
004 Oar 1 pair
P5L334ASS19
005 Air pump 1 P3045BASS16
004
006 Pressure gauge 1
P5C403ASS16
007 Drain valve 1
F3C092ASS14
008 Repair kit 1
P6J718ASS18
Part No. Description QTY SPARE PART NO.
001 Boat 1
P04761
002 Bench seat 1 P6876ASS17
003 Oar 1 pair P5H666ASS19
004 Pressure gauge 1 P5C403ASS16
002
005 Air pump 1
P3045BASS16
006 Drain valve 1
F3C092ASS14
004
007 Airdeck floor 1 P03779
008 Base board 1 P03863
009 Repair kit 1 P6J718ASS18
005
010 Bag 1 P04284
Part No. Description QTY SPARE PART NO.
009
001 Boat 1 P04762
P6876ASS17
002 Bench seat 2
001
003 Oar 1 pair P5H666ASS19
004 Pressure gauge 1 P5C403ASS16
002
005 Air pump 1 P3045BASS16
006 Drain valve 1 F3C092ASS14
004
007 Airdeck floor 1 P03781
P03864
008 Base board 1
009 Repair kit 1 P6J718ASS18
005
010 Bag 1 P04283
#65062
008
001
002
007
003
004
006
005
010
WARNING: To avoid damage to the boat and injury to passengers, please don't exceed the data given on the
builder's plate.
Technical Specifications
Recommended
Item Size
working pressure
7'6" x 51" x 13"
3.5 psi
65046
2.30m x 1.30m x 33cm 0.24 bar
3.5 psi
9'2" x 60" x 16.5"
65047
0.24 bar
2.80m x 1.52m x 42cm
10'10" x 64" x 17"
3.5 psi
65049 3.30m x 1.62m x 44cm
0.24 bar
3.5 psi
12'6" x 71" x 18"
65062
3.80m x 1.80m x 46cm 0.24 bar
Note:
- The floorboards must be assembled before inflating the hull.
NOTE: Pressure gauge is for inflation purpose only, and the value of the pressure gauge is just for reference, should
not be used as a precision instrument.
- Only use Bestway approved inflation pumps.
®
- Never use motor-driven high-pressure air pumps as this may result in over-inflation.
- Under and over-inflation will result in safety hazards.
- Always check the inflation pressure before using the boat.
- Never stand on or rest objects on the boat during inflation.
- Never open the cap of air valve while the boat is in use.
- Be sure the valve is tightly closed before using the boat.
Note: When the oars are not in use, lock the oars into the Oar Clasps to avoid damage.
Outboard Motor Installation
With the boat fully inflated and in the water, attach your outboard motor onto Engine Mount at the center of the Transom.
Note:
- Ensure the motor is always fixed on the Transom.
- Read the instruction of outboard motor for correct installation and operation.
- Overpowering a boat can result in serious injury, death or boat damage. The maximum motor power to be used see
marking on the product.
Maintenance
1: Inflate according to the PSI marked besides the valve;
2: To avoid the long-time exposure to sunshine or rain, put the outside cover on top for protection when it not being
used;
3: Clean it with mild soap water and soft cloth in case it is not going to be used for a long time. Dry it before putting
them away. Store it at a dry and shady place and keep it out of reach of Children.
Deflation
Storage
1. Remove the Oars from the oarlocks.
Note: Keep all accessories for future use.
2. Carefully clean the boat using a mild soap with clean water.
Note: Do not use acetone, acid, and/or alkaline solutions.
3. Use a cloth to gently dry all surfaces.
Note: Do not dry the product in direct sunlight. Also, never dry with equipment such as electric blowers. Doing so will
cause damage and shorten the boat's life span.
4. To deflate, open the Air Valves pushing the control stem in and rotating until the valves stay open. Deflate all the hull
chambers at the same time so the air-pressure drops together. This will prevent damage form occurring to the boat's
inner structures.
5. Next deflate the Keel.
6. Disassemble the seat and floor.
7. Fold the boat from front to back to remove additional air. You can also use a pump to drain any remaining air.
REPAIR INSTRUCTIONS:
• Fully clean the area to be repaired.
• Cut the correct size from the repair patch material.
Apply only the amount of glue needed to cover the repair
site.
• Press the repair patch firmly to repair site for 30 seconds.
• Wait for 1 hour before inflation.
Registration (For US/Canada customers only)
If you need to register your boat, please have the boat Hull Identification Number and model name ready and then visit
bestwaycorp.com/support to obtain your Certificate of Origin, or you can send e-mail to service@bestwaycorp.us for the
Certificate of Origin.
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW OWNER WHEN YOU SELL
THE CRAFT.
3
Part No. Description QTY SPARE PART NO.
009
001 Boat 1 P04763
002 Bench seat 2 P6889ASS16
003 Oar 1 pair P5H666ASS19
004 Pressure gauge 1
P5C403ASS16
005 Air pump 1
P3045BASS16
006 Drain valve 1
F3C092ASS14
007 Airdeck floor 1 P03775
008 Base board 1 P03865
009 1
Repair kit P6J718ASS18
010 Bag 1
P04283
Maximum motor
Floor board
Maximum load capacity
pressure power
5 psi 258 kg (568.8 lbs.)
2.25 kW (3 hp)
0.35 bar 2 adults
480 kg (1058.2 lbs.)
5 psi
7.5 kW (10 hp)
3 adults + 1 child
0.35 bar
5 psi
640 kg (1411 lbs.)
11.2 kW (15 hp)
0.35 bar
4 adults + 1 child
5 psi 780 kg (1719.6 lbs.)
18.4 kW (25 hp)
0.35 bar
6 adults
The glue is not included in the repair kit due to shipping
constraints. You can find silicone-based glue at most retail
outlets. Carefully read the warning labels and closely follow
instructions on the back of glue before attempting the
following repair steps.