Seite 1
Bedienungs- und Installationsanleitung Operating and Installation Instruction Schlüsselschalter SS90 Key switch SS90 (Art.-Nr. / Part No. 154428 / 154430) Technische Änderungen 798510.10 G 193724 vorbehalten! Technical changes reserved! 07.2005...
Seite 2
Schlüsselschalter SS90 Bestimmungsgemäßer Gebrauch Dieses Produkt darf nur für die im Katalog und in der technischen Beschreibung vor- gesehenen Einsatzfälle und nur in Verbindung mit den von Esser by Honeywell emp- fohlenen bzw. zugelassenen Fremdgeräten und Komponenten verwendet werden. Warnung...
Schlüsselschalter SS90 Allgemein Der Schlüsselschalter SS90 ist eine universal einsetzbare Schalteinrichtung. Vorzugsweise wird diese zum Scharf-/Unscharfschalten von Einbruchmel- derzentralen (VdS-Klasse A) verwendet. Leistungsmerkmale • Kernziehschutz • zwei optische Kontrollanzeigen • Summer als akustische Quittierung • Anbohrschutz (Option) • zweiter Schaltkontakt (nur Art.-Nr. 154430) •...
Schlüsselschalter SS90 2.1 Montage- und Installationshinweise Abb. 1: Installationshinweis Betriebserde Sicherheitsschrauben und Zahnscheiben Gehäusedeckel Anbohrschutz (Option) aP-Gehäuse Dekor-Rahmen zusammen mit uP-Dose für uP-Wandeinbau (Art.-Nr. 154438) oder zusammen mit Spangen für Hohlwand- einbau (Art.-Nr. 154439) verwenden Spangen uP-Dose...
Schlüsselschalter SS90 Installation • Gehäusedeckel und Abbohrschutz (falls vorhanden) entfernen. • Anschlusskabel einführen. • Gehäuse auf der Montagefläche ohne mechanische Verspannung mit 4 Schrauben befestigen. • Bei Hohlwand- bzw. uP-Wandeinbau, die den Bausätzen beiliegende Installationsanleitung beachten. • Nach vollständiger Installation, Gehäuse mit den Sicherheitsschrauben verschließen.
Schlüsselschalter SS90 2.3 Montage Profilhalbzylinder Mit der beiliegenden Innen-Sechskant-Schraube den Profilhalbzylinder im Gehäuse befestigen. Unterschiedliche Zylinderlängen werden mit den selbstklebenden Unterlegstreifen ausgeglichen (siehe Tabelle). Der Profilhalbzylinder muss mit dem Gehäusedeckel bündig abschließen. Zusätzlich ist bei der Montage des Profilhalbzylinders, die Schließnasenstellung zu beachten! Zylinderlänge Unterleg- weiß...
Schlüsselschalter SS90 Technische Daten Betriebsspannungsbereich 8 V DC bis 18 V DC Nennspannung 12 V DC Kontaktbelastung Schalter S1 bis S4 max. 30 V DC / 500 mA Stromaufnahme je LED : ca. 20 mA Summer : ca. 5 mA optische Anzeigen LED, rot / LED, gelb akustischer Signalgeber...
Seite 19
Operating and Installation Instruction Key switch SS90 (Part No. 154428 / 154430) 798510.10 G 193724 Technical changes reserved! 07.2005...
Seite 20
This product must only be used for the applications outlined in the catalogue and the technical description and in combination with external components and systems which have been approved or recommended by Esser by Honeywell. Warning In order to ensure correct and safe operation of the product, all guidelines concerning its transport, storage, installation, and mounting must be observed.
Seite 21
Key switch SS90 Table of contents Page General ..................22 Overview ..................23 ....... 25 Assembly and installation information .......... 26 Modified function for switch S4 ........... 27 Assembly of half cylinder Technical specifications ..............28 Wiring..................29 Intruder alarm panel 5004/6 and ..........31 hazard alarm computer 2001 ..........
Key switch SS90 General Key switch SS 90 is a switching system with universal uses. It is preferably used to arm/disarm burglar alarm systems (VdS Class A). Features • Cylinder protection • Two visual control displays • Buzzer for acoustic acknowledgement •...
Key switch SS90 Overview SoFu Sabo NO C +LED- +SUM- +LED- 9 10 11 12 Fig. 1: Overview and position of the components...
Seite 24
Key switch SS90 LED display - red LED display - yellow Buzzer DIL switch setting depending on the panel that is connected (see also resistor value R4 to R8) (See Section 4 for coding) Solder jumper – micro switch S 1 (Coding, see Section 4) Default setting 1 2 3...
Key switch SS90 2.1 Assembly and installation information Fig. 1: Installation information System ground Safety screws and tooth lock washers Housing lid Power drill protection (optional) Surface mounted housing Use decorative frame with flush mounted socket for flush mounted installation (Part No. 154438) or together with clasps for cavity wall installation (Part No.
Key switch SS90 Installation • Remove housing lid and power drill protection (if applicable) • Insert connection cable • Fix housing to the surface with 4 screws without any mechanical strain. • In the case of a cavity wall or flush mounted installation, read the enclosed installation instructions.
Key switch SS90 2.3 Assembly of half cylinder Fix the half cylinder in the housing with the Allan screw. Balance out differing cylinder lengths with the adhesive underlay strips (see Table). The half cylinder must be flush with the housing lid. When you are assembling the half cylinder, pay attention to the latch setting.
Key switch SS90 Technical specifications Power supply range 8 V DC to 18 V DC Rated voltage 12 V DC Contact load switch S1 to S4 max. 30 V DC / 500 mA Current consumption per LED: approx. 20 mA Buzzer: approx.