Herunterladen Inhalt Inhalt Diese Seite drucken

Applying Wax / Polish With The Terry Bonnet; Switching On The Device And Waxing / Polishing The Paintwork; Polishing Or Removing Wax With The Synthetic Polishing Bonnet; Cleaning And Maintenance - Parkside XQ90 Originalbetriebsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 36
Operation / Cleaning and Maintenance / Service centre
©
Applying wax / polish
with the terry bonnet
1. Always use high quality products for waxing.
Follow the working methods given on the
packaging.
2. Apply the wax / polish directly on the working
surface of the terry bonnet
Spread the wax / polish so that it forms a thin,
even, complete coating over the terry bonnet
Note: Too much wax does not necessarily
achieve a better finish and you will have to
spent more time later removing the coating.
3. Spread the wax evenly right up to the edge of
the terry bonnet
5
©
Switching on the device and
waxing / polishing the paintwork
Note: The paintwork to be polished must be care-
fully cleaned and completely dry. If necessary, use
a paintwork cleaner. Use products that are appro-
priate for the demands on and condition of your
paintwork. Heavily oxidised paintwork will require
the use of a special cleaner. For this use a combined
product (cleaner + wax).
1. Place the car polisher on the surface to be pol-
ished.
Note: To avoid the splattering of wax or polish,
do not switch the appliance on yet. Dab the
appliance a few times at various points on the
area to be buffed. In this way you can ensure
that excess wax / polish is once more distributed
evenly over the terrycloth bonnet and the area
to be buffed.
2. Take both appliance grips
hands and switch the appliance on by pressing
the ON / OFF switch
3. Guide the waxer/polisher evenly over the
paintwork (see Fig. C).
Note: Do not press on the waxer /polisher!
The self-weight of the car polisher alone
applies sufficient pressure for the waxing / pol-
ishing process.
34 GB/MT
.
5
.
1
firmly in your
3
(see also Fig. B).
4. Switch the appliance off before you remove it
from the area being buffed. To do this, release
the ON / OFF switch
Any difficult to reach corners or recesses may
have to be completed later by hand. Take the
terry bonnet
the bonnet for the corners and recesses.
©
Polishing or removing wax with
.
5
the synthetic polishing bonnet
Note: The wax / polish must be allowed to dry on
sufficiently to produce the best polishing performance.
Otherwise any polish that is still fluid will be smeared
by the polishing bonnet.
Use the synthetic polishing bonnet
polishing or removing the wax.
When working, always follow the instructions
for use of the wax / polish.
©

Cleaning and Maintenance

WARNING!
the device off and pull the plug out of the mains socket
before carrying out any work on the device.
CAUTION! Ensure that no fluids can permeate into
the appliance, this could lead to the destruction of
the product.
The appliance is maintenance-free.
Use a slightly moist cloth to clean the housing,
if necessary with a mild detergent.
When cleaning the housing, under no circum-
stances should you use strong detergents,
solvents or abrasives.
Clean the bonnet by washing by hand in
soapy water.
©

Service centre

½
WARNING!
paired only by qualified specialist
personnel using original manufactur-
.
3
off the car polisher and use
5
6
DANGER OF INJURY! Switch
Have your device re-
for final

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis