Introduction; Device Description (Fig. 1-15); Supplied Package; Intended Use - Parkside PDS 120 B2 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

2. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
we hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service techni-
cians,
• Installation and replacement of non-original spare parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due to the
non-compliance of the electric regulations and VDE regula-
tions 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt and
moisture. Read the instruction manual each time before operat-
ing the machine and carefully follow its information.
The machine can only be operated by persons who were in-
structed concerning the operation of the machine and who are
informed about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety instructions contained in this operating
manual and the specific regulations of your country, the techni-
cal rules generally accepted for the operation of machines of
the same type must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.

3. Device description (fig. 1-15)

1. Blow-off device
2. Mounting (Blow-off device)
3. Knurled screw
4. Holder (Saw blade guard)
5. Saw blade guard
6. Saw table
7. Foot pedal
8. Cover, left
9. Storage box
10. Bearings
11. Tightening lever
12. Arm
13. Graduated scale
14. Locking lever
15. Suction connection & suction adapter
16. ON/OFF switch
17. Operating mode selection switch
18. Speed regulator
19. Assembly points
20. Work lamp
21. ON / OFF switch work lamp
22. Sawblade
23. Allen key, 3 mm
24. Retaining device
25. Screw (retaining device)
26. Table insert
27. Saw blade holder, top
28. Upper saw blade clamping screw
29. Lower saw blade clamping screw
30. Saw blade holder, bottom
31. Angle (not included in the scope of delivery)
32. Screw (degree scale)
33. Pointer
34. Screw (left cover)
35. Screw (left cover)
36. Fine-wire fuse

4. Supplied package

• Scroll saw
• Saw blade guard (5) with depressor (24)
• Blow-off device (1)
• Saw blade (22) for wood and plastics (4x)
• 1 bolt bag: 4 hexagonal bolts M8 x 50,
4 hexagonal nuts M8, 8 washers
• Hexagon socket screw 3 mm (23
• Suction adapter
• Original operating instructions

5. Intended use

The fretsaw was designed to cut square-edged timber or other
workpieces such as Plexiglas, glass fiber reinforced plastic,
foam, rubber, leather, and cork. Do not use this saw to cut
round materials. Round materials can easily become jammed.
Risk of injury! Parts can be catapulted!
GB/IE/NI 3