Additional Safety Instructions - Parkside PDS 120 B2 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

– Check the connection cable of the electric tool regu-
larly and have it replaced by a recognised specialist
when damaged.
Check theextension cable regularly and replace it if
–
damaged.
– Keep handles dry and free from oil and grease.
15. Pull the connector out of the socket
– When the electric tool is not in use or prior to mainte-
nance and when replacing tools such as saw blades,
bits, milling heads.
16. Always remove keys and wrenches after use
– Always check that keys, wrenches and other adjusting
tools have been removed before you switch on the
equipment.
17. Avoid unintentional starting
– Make sure that the switch is turned off when connecting
the tool to the power supply.
18. Use extension cables for outdoors
– Check that it is approved for outdoor duty and is
marked accordingly.
19. Be alert at all times
– Watch what you are doing. Use common sense when
working. Never use the tool when you are distracted.
20. Check the electric tool for potential damage
– Protective devices or other parts with minor damage must
be carefully inspected to ensure that they function correctly
and as intended prior to continued use of the electric tool.
– Check whether the moving parts function faultlessly and
do not jam or whether parts are damaged. All parts
must be correctly mounted and all conditions must be
fulfilled to ensure fault-free operation of the electric tool.
– Damaged protective devices and parts must be prop-
erly repaired or replaced by a recognised specialist
workshop, insofar as nothing different is specified in
the user manual.
Damaged switches have to be replaced by a customer
–
service workshop.
Do not use any electric tool on which the switch cannot
–
be switched on and off.
21. ATTENTION
– The use of other insertion tools and other accessories
can entail a danger of injury.
22. Have your electric tool repaired by a qualified
electrician
– This electric tool conforms to the applicable safety
regulations. Repairs may only be performed by an
electrician using original spare parts. Otherwise ac-
cidents can occur.
WARNING
This electric tool generates an electromagnetic field during op-
eration. This field can impair active or passive medical implants
under certain conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with medical
implants consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.

6.2 Additional safety instructions

• Switch the machine off immediately and pull the power plug
in an emergency.
• Follow all these safety instructions before and while working
with the saw.
• Do not use this saw to cut fire wood.
• Do not use this saw to cross-cut roundwood without a suit-
able holding device.
• The machine is equipped with a safety switch to prevent it
from being switched on again accidentally after a power
failure.
• If you need to use an extension cable, make sure its conduc-
tor cross-section is big enough for the saw's power consump-
tion. Minimum cross-section 1,5 mm
• If you use a cable reel, the complete cable must be pulled
off the reel.
• Persons working on the machine should not be distracted.
• After you have switched off the motor, never slow down the
saw blade by applying pressure to its side.
• Only fit blades which are well sharpened and have no cracks
or deformations.
• Faulty saw blades must be replaced immediately.
• Never use saw blades which do not comply with the data
specified in this manual.
• It is imperative to make sure that all devices which cover the
saw blade are in good working order.
• Never dismantle the machine's safety devices or render them
inoperative.
• Damaged or faulty safety devices have to be replaced im-
mediately.
• Never cut workpieces which are too small to hold securely
in your hand.
• Never load the machine so much that it cuts out.
• Always press the workpiece firmly against the saw table.
• Never remove loose splinters, chips or jammed pieces of
wood when the saw blade is running.
• Switch the machine off to rectify faults at the blocked plug-in
tool. - Pull the power plug- Remove the blockage. Important!
Risk of injury from saw blade! Wear gloves. Carry out a trial
run without a workpiece. Ensure that no unusual noise or
vibration occurs. Should this be the case, switch the unit off
and contact the manufacturer.
• Carry out retooling work, adjustments, measurements and
cleaning jobs only when the motor is switched off. - Pull the
power plug. -
• Before switching on, make sure that all keys and wrenches
have been removed from the tool.
• Switch off the motor and pull the power plug before you
leave the workplace.
• Electrical installation work, repairs and maintenance may
only be carried out by persons who have been specially
trained.
• Refit all guards and safety devices immediately after you
have completed any repairs or maintenance work.
• Be sure to observe the safety information and operating and
maintenance instructions issued by the manufacturer, as well
as the dimensions listed in the Technical Data.
• It is imperative to observe the accident prevention regula-
tions in force in your area as well as all other generally rec-
ognized rules of safety.
• Note the information published by your professional asso-
ciations (VBG 7).
• The saw is intended to be used indoors only.
.
2
GB/IE/NI 5