Optional Accessories - Makita RP1800 Bedienungsanleitung
Vorschau ausblenden
Andere Handbücher für RP1800:
- Bedienungsanleitung (80 Seiten) ,
- Betriebsanleitung (73 Seiten) ,
- Betriebsanleitung (73 Seiten)
Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Replacing carbon brushes
► Fig.35: 1. Limit mark
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
► Fig.36: 1. Brush holder cap 2. Screwdriver
After replacing brushes, plug in the tool and break in
brushes by running tool with no load for about 10 min-
utes. Then check the tool while running and electric
brake operation when releasing the switch trigger. If
electric brake is not working well, ask your local Makita
service center for repair.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
•
These accessories or attachments are recom-
mended for use with your Makita tool specified
in this manual. The use of any other accessories
or attachments might present a risk of injury to
persons. Only use accessory or attachment for
its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
•
Straight & groove forming bits
•
Edge forming bits
•
Laminate trimming bits
•
Straight guide
•
Trimmer guide
•
Guide holder
•
Templet guides
•
Templet guide adapter
•
Lock nut
•
Collet cone 12 mm, 1/2"
•
Collet sleeve 6 mm, 8 mm, 10 mm
•
Collet sleeve 3/8", 1/4"
•
Wrench 24
•
Vacuum head set
Router bits
Straight bit
► Fig.37
D
A
6
20
1/4"
12
12
1/2"
12
10
1/2"
8
8
6
8
1/4"
6
6
1/4"
"U"Grooving bit
► Fig.38
D
A
6
6
"V"Grooving bit
► Fig.39
D
A
1/4"
20
Drill point flush trimming bit
► Fig.40
D
A
12
12
8
8
6
6
Drill point double flush trimming bit
► Fig.41
D
A
6
6
Board-jointing bit
► Fig.42
D
A 1
12
38
Corner rounding bit
► Fig.43
D
A 1
A 2
25
9
6
6
20
14 ENGLISH
L 1
L 2
50
15
60
30
60
25
60
25
50
18
50
18
L 1
L 2
50
18
L 1
L 2
50
15
90
L 1
L 2
L 3
60
20
35
35
60
20
18
28
60
L 1
L 2
L 3
L 4
70
40
12
14
A 2
L 1
L 2
27
61
4
L 1
L 2
L 3
48
13
5
45
10
4
8
mm
mm
R
3
mm
mm
mm
mm
L 3
20
mm
R
8
4
Werbung
Inhaltsverzeichnis
