Introduction; Device Description (Fig. 1-2); Scope Of Delivery; Intended Use - Parkside PUG 1600 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

1. Introduction

MANU FACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D- 89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the man-
ufacturer of the device does not assume liability for dam-
ages to the product or damages caused by the product that
occurs due to:
• Improper handling,
• Non- compliance of the operating instructions,
• Repairs by third parties, not by authorized service tech-
nicians,
• Installation and replacement of non- original spare parts,
• Application other than specified.
We recommend:
Read through the complete text in the operating instructions
before installing and commissioning the device.
The operating instructions are intended to help the user to
become familiar with the device and take advantage of its
application possibilities in accordance with the recommen-
dations.
The operating instructions contain important information
on how to operate the device safely, professionally and
economically, how to avoid danger, costly repairs, reduce
downtimes and how to increase reliability and service life
of the machine.
In addition to the safety instructions in these operating
instructions and the safety instructions for the machine
mounted, you must also observe your country's regulations
applicable to the operation of this device and the electric
power tool mounted.
Keep the operating instructions package with the device at
all times and store it in a plastic cover to protect it from dirt
and moisture. Read the instruction manual each time before
operating the device and carefully follow its information.
The device can only be operated by persons who were in-
structed concerning the operation of the machine and who
are informed about the associated dangers.
m Attention
The electric power tool mounted on the universal tool stand
may only be used by personnel who have been trained in
the use of the electric power tool and who have been in-
structed with respect to the associated hazards.
The minimum age requirement must be complied with.
In addition to the safety instructions in this operating manual
and the separate regulations of your country, the generally
recognised technical rules relating to the operation of such
devices must also be observed.
8 GB/IE
We accept no liability for damage or accidents which arise
due to non- observance of these instructions and the safety
information.

2. Device description (Fig. 1-2)

A. Universal tool stand
B. Support arm
C. Crossbar
D. Adjustable workpiece support
E. Screw
F. Screw
G. Washer
H. Spring washer
I. Nut
J. Star- grip screw (small)
K. Star- grip screw (large)

3. Scope of delivery

1x Universal tool stand (A)
2x Support arm (B)
2x Crossbar (C)
2x Adjustable workpiece support (D)
4x Screw M6x16 (E)
4x Screw M6x60 (F)
8x Washer 6mm (G)
8x Spring washer 6mm (H)
8x Nut M6 (I)
4x Star- grip screw (small) (J)
2x Star- grip screw (large) (K)
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport dam-
age.
• If possible, store the packaging until the warranty period
has expired.
ATTENTION
The device and packaging materials are not toys! Chil-
dren must not be allowed to play with plastic bags,
film and small parts! There is a risk of swallowing and
suffocation!

4. Intended use

Always observe the proper use of your universal tool stand.
The universal tool stand is designed for use with tabletop de-
vices such as mitre saws, scroll saws, circular table saws,
etc.
Electric power tools without suitable mounting holes are not
permitted to be fitted to the universal tool stand and shall
not be operated in conjunction with the universal tool stand.
Electric power tools must be firmly bolted to the universal
tool stand before starting them up.